ESPixelStick Progra...
 
Notifications
Clear all

ESPixelStick Programming Help

32 Posts
6 Users
0 Reactions
8,956 Views
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

If it didn't change the controller back to DHCP then it likely did not program. If you are following instructions, including trying to flip Tx & Rx, on the ESPixelStick, then your Programmer is likely the issue. Plus, you may not need to reprogram - - maybe you should update instead.

Build an EFU File.
- Start ESP Flash Tool - Travis
- Fill in the SSID and PassPhase
- And select firmware (Pixel or Serial)
- Press Build EFU
- Save the file in the EXPFlashTool Directory.

Using a WEB browser (Not IE) and a wireless connection; access 192.168.1.148 - goto ADMIN tab and upload your EFU file
Pixel = espixelstick.efu Serial = espixelstick.efu
Wait 2 to 3 minutes. If ESPixelStick does not reset = restart using the IP address again.
Make desired changes as needed via WEB, not reprogramming.


Reply
Posts: 42
(@vitohgrind)
Trusted Member
Joined: 8 years ago

I've had trouble running Travis's latest releases (all of the ones from 2019). Even once installed, the ESPs would stop responding after about a few minutes. There's some nice features he has built in, but it was definitely too unstable for me. You may want to save yourself the trouble and stick with the official release firmware.


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

I been running Travis for over a year, including show in 2018. I’ve been working current version since it’s release mid October 2019. No issues.

For those experiencing problems, check your network and power....very likely not Travis. Too many users without issues to suspect Travis is at fault.


Reply
Posts: 42
(@vitohgrind)
Trusted Member
Joined: 8 years ago
mrGrumpy wrote:I been running Travis for over a year, including show in 2018. I’ve been working current version since it’s release mid October 2019. No issues.

For those experiencing problems, check your network and power....very likely not Travis. Too many users without issues to suspect Travis is at fault.

Interesting. I thought it might've been power, because it runs longer before hanging when connected to the pc, but it still hangs. I double checked my input voltage and was steady right at 5v. For the network, I could ping the ESPs all day and would get responses, but when loading the internal sites and when running the show from xlights, I would get slow to no response. For example the main form of the page would load, but the data (network info, uptime, etc) never would. The network is completely separate running on a Netgear Nighthawk placed at the front of the garage.

Are there settings on the router (qos, etc) that I should tweak or adjustments to input power I need to make? I would prefer Travis's build but so far it just wasn't working for me.

Sent from my SM-N950U using Tapatalk


Reply
Posts: 125
Topic starter
(@mmais68569)
Estimable Member
Joined: 17 years ago
VitoHGrind wrote:I've had trouble running Travis's latest releases (all of the ones from 2019). Even once installed, the ESPs would stop responding after about a few minutes. There's some nice features he has built in, but it was definitely too unstable for me. You may want to save yourself the trouble and stick with the official release firmware.

I have to update. I am running 142 nodes on a model & it keeps blowing fuses. With the update I can drop the brightness.
Mike


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

VitoHGrind, I’ve had similar issues when running unicast, but when changes to Multicast for the ESPixelSticks, those problems went away.


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago
mmais68569 wrote:I have to update. I am running 142 nodes on a model & it keeps blowing fuses. With the update I can drop the brightness.
Mike

What size fuse are you blowing.....I don’t think brightness control is going to help.


Reply
Posts: 1592
(@ruppro)
Noble Member
Joined: 11 years ago
mmais68569 wrote:I have to update. I am running 142 nodes on a model & it keeps blowing fuses. With the update I can drop the brightness.
Mike

I am running over 500 (w/ power injection) and no blown fuses - sounds like there is a short somewhere


Reply
Posts: 125
Topic starter
(@mmais68569)
Estimable Member
Joined: 17 years ago

Thanks Mr. Grumpy
I was finally able to get the controller updated. Now I have a question on the Travis version. There are two settings 1. Group size
what should this be set to? I am running 142 nodes on this controller. 2. Brightness is set to 1 & I want to run the brightness at 30-40% is this what I should put in this box?
Thanks so much for all your help
Mike

192.168.1.148

Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago
mmais68569 wrote:Thanks Mr. Grumpy
I was finally able to get the controller updated. Now I have a question on the Travis version. There are two settings 1. Group size
what should this be set to? I am running 142 nodes on this controller. 2. Brightness is set to 1 & I want to run the brightness at 30-40% is this what I should put in this box?
Thanks so much for all your help
Mike

Please share with others what finally worked. We can learn from what worked for you.

Group is how main pixels will light when you call for one to light. If you put a 3 there each sequenced pixel will light 3 pixels as 1. RGB Rainbow at 1 would be R-G-B-R-B-G- Set at 3 would be R-R-R-G-G-G-B-B-B-

Brightness is a setting of 0.1 Thru 1.0 so 50% would be 0.5


Reply
Page 2 / 4
Share: