How much power do you fell you can push through those connectors you listed?
I like both the price and the availability.
ukewarrior wrote:How much power do you fell you can push through those connectors you listed?
I like both the price and the availability.
I'm not really sure about the capacity of these connectors. I saw that they were 22 AWG and did a little searching of these forums. I found this thread (among others) that gave me the idea that 22 AWG wouldn't be an issue, since it seems like the pixel wires are probably 22 AWG. The wires on my pixels look pretty thin, while the wires on these connectors are a but thicker, so I feel like I'm in good shape there.
I replaced every connector at the base of my mega-trees with these waterproof connectors. I also added a 2-wire waterproof connector at every power injection point. Every injection point (except the first one where the board connects) is receiving power from the power supply. I even created a custom 3-pin to 2-pin adapter to inject power into the last string (my trees are 270 degrees). At the top of my tree, I got a little lazy and just left the standard (non-waterproof) connectors, which I didn't have any issues with last year. That didn't work out so well for me this year, as some water got into one of the connectors and shut down the tree from that string forward. Luckily, I was able to dry it out, and as a workaround (rather than taking my whole tree apart) for this year, I coated the non-waterproof connectors in hot glue. I plan to replace those connectors after I take the lights down.
With as much power injection as I'm using, I don't think I'm putting too much power through any individual connector. With that in mind and me not having an expansive knowledge of how to really assess the capacity of these connectors, what would you say would be issues or symptoms I would have if I were feeding too much power through these connectors? I've had 'pinking' in my strings, but power injection has taken care of that. I haven't noticed any warm wires (as I would expect if I were overloading something). I've had issues in the past with my strings 'freezing up' when I turn them on full white, but I've subsequently discovered that to be a result of an inadequate power supply.
Finally, here is the wire I started using this year. It's definitely less cumbersome that lamp cord and if I understand correctly, is the same gauge. I did get some pinking when I made up a 15 foot 'extension cord' of this cable in order to have both of my mini-trees (at the bottom of the steps) on the same controller, but was able to resolve this by adding a T on the end of the extension and using the additional output for power injection.
Overall, I'm happy with the connectors and with the wire, to the point that I purchased 50 of both the 2-pin and 3-pin connectors to come over on the boat at some point. It might be worth noting that I have a relatively small yard, so I'm not sure if my solutions would work well for everyone, but I don't have any issues to report as of yet and other than losing those little red O-rings, I like how these connectors fit together and find them much more convenient than my previous connection methods (directly soldering connections or using lamp cord with vampire plugs than wrapping the vampire plugs in electrical tape).
Hope this info helps. :happy:
The wire you have referenced is "Copper Clad/Coated Aluminum wire". I would RUN away from that. I went that way to save money and it caused nothing but issues. You will get a year or two out of it and then it will corrode and cause heartache. Instead look at this one ( https://www.amazon.com/gp/product/B07SKGTCWQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 ). It comes in 3 and 4 wire, pure copper, and 18 awg.
Joey
I use non waterproof JST connectors. I have had some of them laying in water (not on purpose) and had no issue. Some of those connectors have been in service for five seasons. I also put a few (liberal) drops of corrosion-x gun oil IN every connector. Have never had a water related issue. Rodents, people, trees are different stories. Also, the JST style connectors seem to have a limited insertion lifetime that I seem to easily reach.
joeytx wrote:The wire you have referenced is "Copper Clad/Coated Aluminum wire". I would RUN away from that. I went that way to save money and it caused nothing but issues. You will get a year or two out of it and then it will corrode and cause heartache. Instead look at this one ( https://www.amazon.com/gp/product/B07SKGTCWQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 ). It comes in 3 and 4 wire, pure copper, and 18 awg.Joey
Good catch. I didn't even notice that. I knew to steer clear of CCA in network cabling, but wasn't paying close attention when I bought this. I suppose this wire might be okay when used inside walls for its intended purpose with alarm systems, but I can see how it will probably cause issues when it's subject to temperature changes and occasional flexing.
I haven't incorporated this wire into any of my models (although I was planning to) and have only used it to run power and power injection to my models (other than that one 15' extension cord), so I may bUy some better cable and replace it as this CCA craps out.
Sent from my LM-G710 using Tapatalk
