ESpixelStick Networ...
 
Notifications
Clear all

ESpixelStick Network configuration

19 Posts
6 Users
0 Reactions
4,891 Views
Posts: 255
Topic starter
(@townshend-lights)
Reputable Member
Joined: 11 years ago
[#53240]

On the ESpixelStick Network configuration page, in Static ip setting, what should the gateway be?
Should it be the gateway of my Access point or of the Raspberry Pi?
Or should the access point also be the same as my Raspberry Pi so it completes the circuit of data out to the controllers and back into the Pi?


18 Replies
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

The gateway address depends on how your network is configured. We would need to know your network topology to tell you what the gateway would be.


Reply
TomL8345
Posts: 1356
(@toml8345)
Noble Member
Joined: 15 years ago

My show network consists of a RPi connected directly to my AP (Ubiquiti Nano Loco M2) with 18 static IP Pixelsticks. I have my sticks set for the Gateway of my RPi Eth0, with the RPi Lan0 connecting to my Home Network as a bridge.

HTH


Reply
Posts: 255
Topic starter
(@townshend-lights)
Reputable Member
Joined: 11 years ago

Tom, do you have any lag issues? Whats the most pixels you have on a stick?
My Mega tree has 1185 pixels and my Matrix has 1224. I read somewhere that the max is 690? and 4 universes. I was wondering if this is causing the Lag?


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
townshend lights wrote:Tom, do you have any lag issues? Whats the most pixels you have on a stick?
My Mega tree has 1185 pixels and my Matrix has 1224. I read somewhere that the max is 690? and 4 universes. I was wondering if this is causing the Lag?

WRT to 690: 680 is the most pixels you should have on a string to achieve a 25ms refresh rate. Going above this simply slows down refresh rate. It does not cause lag. In most cases lag is caused by unicast on wifi, incorrect wifi broadcast speed, too much traffic on the WiFi (This is where a lot of pixels can cause lag). Too many pixels on the WiFi is hard to do. A few thousand pixels would not in themselves cause significant lag.


Reply
Posts: 255
Topic starter
(@townshend-lights)
Reputable Member
Joined: 11 years ago

That raises more questions 🙂 What is WRT? I used the term Lag but What happens is the sequence will run and slow down, pause and then quickly catch up. I'm using Static on a Dlink Dap2690 commercial AP.
I've tried to switch to multicast, but can't figure out how to get Xlights to upload the config to the controllers without reflashing ESPixelstick manually again. The little indicator light on the controller screen of xlights doesn't change to green or red. It just stays grey. I can however connect directly to each controller in multicast mode from a fresh reflash as it shgows me the IP address in Homeflasher. From there I can set each universe, pixel count etc. It's just Xlights can't see them.

In my AP I have turned on IGMP snooping, made sure DHCP is active.

I've tried to find a walk though or video to help me but they are either too old or not quite in dept enough to help me set up multicast.


Reply
Posts: 255
Topic starter
(@townshend-lights)
Reputable Member
Joined: 11 years ago

Oh and another question, is it a good idea to run multicast with leased ips on dhcp? That way the ip of the controller wouldn't change, so technically not set as static? Or am I over thinking this?

Sent from my YAL-L21 using Tapatalk


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago
Reply
wilmar
Posts: 2115
(@wilmar)
Noble Member
Joined: 8 years ago
townshend lights wrote:That raises more questions 🙂 What is WRT? I used the term Lag but What happens is the sequence will run and slow down, pause and then quickly catch up. I'm using Static on a Dlink Dap2690 commercial AP.
I've tried to switch to multicast, but can't figure out how to get Xlights to upload the config to the controllers without reflashing ESPixelstick manually again. The little indicator light on the controller screen of xlights doesn't change to green or red. It just stays grey. I can however connect directly to each controller in multicast mode from a fresh reflash as it shgows me the IP address in Homeflasher. From there I can set each universe, pixel count etc. It's just Xlights can't see them.

In my AP I have turned on IGMP snooping, made sure DHCP is active.

I've tried to find a walk though or video to help me but they are either too old or not quite in dept enough to help me set up multicast.

Are you playing through xlights off pc or FPP with a pi ?

Sent from my iPhone using Tapatalk


Reply
Posts: 255
Topic starter
(@townshend-lights)
Reputable Member
Joined: 11 years ago

I have all of them. So up until last week I would upload the sequence from xlights on to my Pi running FFP. When I installed my new Matrix, the "lag -lack of a better word" started happening.
I am running static IP's. After A LOT or research it seamed to be that most people suggested Multicast was the way to go, So I've been messing around with trying to get that to work.

So while I'm getting it sorted I'm controlling the lights with Xlights (not Xschedule) and when it's right I'll start using the PI again.
In Xlights the protocol I'm using is DDP static.


Reply
Page 1 / 2
Share: