ESPixelStick Flash ...
 
Notifications
Clear all

ESPixelStick Flash Tool

223 Posts
49 Users
0 Reactions
100.3 K Views
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
jwamsley07 wrote:I tried this last night with a couple ESPixelsticks I had from last year. So much easier programming them this way. Many Thanks!! On V1.3, there was a problem using static IPs, at least on my end. I like to put static ip addresses on all my equipment and was curious if any problems on v1.5 before I tried it.

There have been changes to the way static IP's are assigned (fix from Materdaddy), so I'd give it another shot. I personally haven't tested static IP's lately as I use DHCP, but it's on my list. Note that if you want to use static IP's with the flash tool, you'll need to edit "data/spiffs/config.json", change your settings, and set "dhcp" to false. I may add an advanced tab to edit all the settings in the future, but wanted to keep the tool simple as possible.

Also note, the firmware included with the tool is beta and will be changing. 1.5 will never be final as I plan on rolling straight into 2.0 once I get the combined OTA (sketch + spiffs) code done. The OTA update code in 1.5 beta was just me testing sketch updates and won't be able to update using the firmware packages I'll be releasing after 2.0. I'm not sure if the new UI will be ready for 2.0 yet or not, however you'll be able to update via the web interface from 2.0 onward.


Reply
michaelc
Posts: 1540
(@michaelc)
Noble Member
Joined: 19 years ago

I just pulled out my ESPixelSticks from last year and I'm connecting to my newly build Renard SS24 in DMX mode. The current FW Version is 1.4. I"m reading through this thread about the new upload tool and have some questions. 1) I found the zip file and downloaded. 2) I see you mentioned a version 1.5 but it's beta. What does 1.5 give you that was missing in 1.4? Finally, 3) what is the connection needed to flash the ESPixel. Are we still connecting through a USB FTDI adapter or does this now just go over the wireless? Also I see mention of swapping serial pins. I"m assuming if the answer to 3 is USB/FTDI it has something to do with remapping pins. I recall at one point I had to add a resistor somewhere as well. What is the physical connection to flash?


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
michaelc wrote:I just pulled out my ESPixelSticks from last year and I'm connecting to my newly build Renard SS24 in DMX mode. The current FW Version is 1.4. I"m reading through this thread about the new upload tool and have some questions. 1) I found the zip file and downloaded. 2) I see you mentioned a version 1.5 but it's beta. What does 1.5 give you that was missing in 1.4? Finally, 3) what is the connection needed to flash the ESPixel. Are we still connecting through a USB FTDI adapter or does this now just go over the wireless? Also I see mention of swapping serial pins. I"m assuming if the answer to 3 is USB/FTDI it has something to do with remapping pins. I recall at one point I had to add a resistor somewhere as well. What is the physical connection to flash?

The connection to flash is still the same. A list of changes can be found here - https://github.com/forkineye/ESPixelStick/blob/master/Changelog.md . 1.5 will actually be rolled to 2.0 by the end of this week, along with a new release of the flash tool. The pin swapping is for people who are trying to use the pre-compiled ESPixelStick firmware on other ESP platforms. All you need to do is feed the data line and ground to the serial input on the Renard. I'm not familiar with the Renard SS25, but I'm sure others can chime in on that part.


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Most l;ikely you will need to switch the renard firmware to use the renard protocol instead of DMX.


Reply
michaelc
Posts: 1540
(@michaelc)
Noble Member
Joined: 19 years ago
MartinMueller2003 wrote:Most l;ikely you will need to switch the renard firmware to use the renard protocol instead of DMX.

Why? I thought it supports DMX mode. Did I miss something somewhere?


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

OK Shelby, now I am confused.

In post #3 you state that the tool will not work with the original version of the ESPixelStick.
It appears that some are using it for the original (version 1) units.

What did I miss? I have quite a few of them (18 or 20 if I remember correctly) and would like to bring them up to the "latest" - if possible.


Reply
sporadic
Posts: 1199
Topic starter
(@sporadic)
Noble Member
Joined: 14 years ago
algerdes wrote:OK Shelby, now I am confused.

In post #3 you state that the tool will not work with the original version of the ESPixelStick.
It appears that some are using it for the original (version 1) units.

What did I miss? I have quite a few of them (18 or 20 if I remember correctly) and would like to bring them up to the "latest" - if possible.

That post was referring to 512kb ESP01 modules. All the ones I've sold with both v1 and v2 kits have been the 1mb modules. It'll work fine with your kits if you got the modules from me or they're 1mb.

Sent from my XT1094 using Tapatalk


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

The problem, I believe, is that the ESP modules with only 512K of RAM can't handle the new code -- the new code is too big. You need the ESP modules with 1MB or more of RAM to load the code onto the module.


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

Thanks for clearing that up. Since I purchased directly from you, I'll give the new program a try. 🙂


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

No, but maybe I did. I do not remember a dmx output mode. However, I did not look for one either.


Reply
Page 2 / 23
Share: