E8604 not respondin...
 
Notifications
Clear all

E8604 not responding to reset

12 Posts
5 Users
4 Reactions
610 Views
Posts: 75
Topic starter
(@mark-m)
Trusted Member
Joined: 3 years ago
[#59024]

Holding the 'PROGRAM' button down on my SanDevices E8604 is not blinking the green & red LEDs as described int he manual. Both lights stay lit.
Is this a hint that there is a hard where fault or is there something else I need to do?


11 Replies
Posts: 849
(@tfischer)
Prominent Member
Joined: 17 years ago

Does the board behave properly in other ways?

Tell us more about the history of the board. Did it once work and stop working now?


Reply
Posts: 75
Topic starter
(@mark-m)
Trusted Member
Joined: 3 years ago

I've been given this board. Unsure of it's history. PCB looks in great condition and it still has the adhesive feet unused.

12v or 5v:
Ethernet indicators come on an flicker.
Red & green indicators stay lit.

Holding down the program button on boot:
Red & green indicators are off and stay off until powered off and on again. I presume that is flashing mode.


Reply
Posts: 503
(@iflights)
Honorable Member
Joined: 14 years ago

I have many Sandevices controllers. You are waiting until the board is booted before pressing the button, right? "Holding down the program button on boot", just want to ensure you are holding down the button AFTER boot.

Are you able to access the board's web page using the default address of 192.168.1.206? What happens when you try?


Reply
Posts: 849
(@tfischer)
Prominent Member
Joined: 17 years ago

If you hold down the program button AFTER boot the LEDs should start flashing.

Then there i a procedure to set a temporary IP address, or have it flash back the IP address that it is currently set to.

You may be able to go into your router and see what IP address the device is consuming, and then use that to access the web interface. But for that to happen the device needs two be on the same subnet as your home network. Most people use 192.168.1.x but my home network uses 192.168.10.x which means I can't just use default addresses much of the time. That was a standard set by a router I used maybe 15 years ago but I have far to many devices now to easily change it lol.


Reply
Posts: 75
Topic starter
(@mark-m)
Trusted Member
Joined: 3 years ago
iflights wrote:
I have many Sandevices controllers. You are waiting until the board is booted before pressing the button, right? "Holding down the program button on boot", just want to ensure you are holding down the button AFTER boot.

Are you able to access the board's web page using the default address of 192.168.1.206? What happens when you try?

I am waiting until it has booted before holding the program button. No flashing by the LEDs when holding down the button.
I tried a different attempt trying to hold it on power up.

I've scanned IPs in the 192.168.1.x, 192.168.0.x, 10.1.1.xx and don't see anything responding.
The default of 192.168.1.206 has no response (no a ping).

I'm unsure if this has been set up already and what the person's network range would have been. If it was setup, it may have just left in it's packaging for years.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

I;d start by re-flowing all solder points. If it was a diy assemble , you may find quick success .

There are many threads on the e6804 .


Reply
Posts: 503
(@iflights)
Honorable Member
Joined: 14 years ago

Don't disagree with the advice. But perhaps limit the scope of the reflow to the button area.

The Red and Green lights are a positive sign after the boot is complete. Tells me the board is functioning.

I suspect the push button switch causing a problem at this point. If you are confident with electronics you can make a quick jumper with a paper clip on the back the board where the push button goes "thru-hole" to simulate what a functioning button press would do.


Reply
Posts: 75
Topic starter
(@mark-m)
Trusted Member
Joined: 3 years ago
iflights wrote:
I suspect the push button switch causing a problem at this point. If you are confident with electronics you can make a quick jumper with a paper clip on the back the board where the push button goes "thru-hole" to simulate what a functioning button press would do.

Using a pair of tweezers to bridge the button does not work.
My guess is the button is connected/working, because it will prohibit boot if held down while power is applied (Green & Red LEDs won't come on).

angus40 wrote:
I;d start by re-flowing all solder points. If it was a diy assemble , you may find quick success .

There are many threads on the e6804 .

I think this is a worthwhile step.
The board appears to be bought finished as all the solder joints look immaculate. Re-flowing them shouldn't hurt...


Reply
JP90
Posts: 376
 JP90
(@jp90)
Reputable Member
Joined: 19 years ago

Here is a link to the SanDevices E6804 User manual, It should help.
https://sandevices.com/wp-content/uploads/2017/11/E6804_Operating_Manual.pdf


Reply
Page 1 / 2
Share: