A couple of stupid questions. The first is purely hardware/1.31 issue.
1) What is the maximum pixels you can run on a single 1 of 16 connector?
I have Vixen installed and have watched some of the videos. I also am expecting an e682 tonight. I have read the manual and it seems pretty straight forward. I want to test a single string of pixels (300 pixels in the string).
2) Can that be done on a single connector? I hate to cut the string before knowing how I will use it. But I do want to do some testing.
3) I won't have any trouble getting the IP set properly, on the e682. And I think the "output" can be managed but what do I need to configure in Vixen, to allow a simple sequence to communicate with my e682? That's not really discussed in any of the videos I have found.
1) Am not sure but it should work, I think its explained in the manual or on the wiki
2) 300 pixel so you mean 100 count.
3) when you go to vixen setup display, controller setup, add where you see blinkylinky click on it scroll down and find streaming ACN(E1.31) select it the click on the + button name your controller
next step click on the newly created controller click on the settings under selected controller enter your universe start size and ip and destination.
Art wrote:1) Am not sure but it should work, I think its explained in the manual or on the wiki
2) 300 pixel so you mean 100 count.
No, it's 300 pixels (RGB combined, in one chip, with 2811 controller. There's a cut point between each pixel, unlike the ones with 3 chips per controller. But I haven't seen anything that specifically puts a pixel count per connector. This is what they look like.
I counted out the first 100 and there was tons left to count, so it's 300 pixels. They are densely packed on the strip. About 100 in 1 meter or so. So the full 300 is about 16 feet.
Any guesses as to whether I can plug them all into a single 1 of 16 connector and address them all. It would take more than 1 universe, if 171 is that limit.
Each LED =3 pixel for instance in your pic it shows 3 LEDs thats 9 pixels, so if you count 100 LEDs = 300 pixels
as far as how many pixel per connector am going to find out ill post it later or maybe somebody else will
I think you can do the 300 pixels in one connector but you have to watch out for the amperage because the fuses are rated for 5 amps only
Also if this is what you are trying to use I just notice your LEDs are not pixels they are whats called dumb RGBs. the pixels should have a tiny microchip next to the LED
Art wrote:Each LED =3 pixel for instance in your pic it shows 3 LEDs thats 9 pixels, so if you count 100 LEDs = 300 pixels
as far as how many pixel per connector am going to find out ill post it later or maybe somebody else will
I think you can do the 300 pixels in one connector but you have to watch out for the amperage because the fuses are rated for 5 amps only
Also if this is what you are trying to use I just notice your LEDs are not pixels they are whats called dumb RGBs. the pixels should have a tiny microchip next to the LED
Your terminology is backwards. You are definitely NOT understanding. the 300 pixels is a given. That is not in dispute. I know, without any doubt, it's 300 pixels (900 individual LEDs, 300 Red, 300 Green, 300 Blue). It's NOT 100 pixels ( a pixel is the sum of RGB LEDs.)
I know, because I counted them. The image above shows 3 pixels. I have 300 of them in a string.
But for everyone now, I still have one issue. I have tested my string, using the built in test. And I have accessed it via the web page. But I can't get Vixen to talk to it, properly.
Here is what I have done:
1) Added a controller, and specified "Streaming ACN (E1.31) as the controller
2) Configured the controller and selected "Multicast Ethernet" (I also tried something called Multicast Local Area Connection *11)
3) Specified the total number of channels required to operate my test string (900 channels)\
4) Created a simple test sequence, of one group, with all 900 channels
5) Added some effects to the group
6) Used Setup Display to map sequence to controller
But when I run the sequence, only the first LED lights. I'm pretty sure I must be setting up my group incorrectly but is there any other step I need to do that might explain only the 1st pixel lighting?

