E682 What am I doin...
 
Notifications
Clear all

E682 What am I doing wrong?

12 Posts
5 Users
0 Reactions
3,549 Views
Posts: 6
Topic starter
(@thevolksman)
Active Member
Joined: 9 years ago
[#47763]

This year I'm finally getting around to setting up my first basic items to ensure I got a handle on things prior to shelling out more money. I built two e682 controllers around 2 years ago. So now I go to setup some lights - three garage doors 228 WS2811 pixels each and a horizontal run across the top of the garage with 336 WS2811 pixels. Using the E682 Controller (V.4XX) using outputs 1-1, 2-1,3-1 and 4-1. Universes numbers setup 1-12. Starting with universe 1 channel 1 on output 1-1. This puts the Ending channel universe 2 channel 174. I start the next out put on Universe 3 channel 1 etc. making sure no overlapping channels.

The only way I was able to get the controller to work correctly using test sequence was I had to enable 2 outputs for 1-1 through 1-4 (garage door#1), and I had to enable 3 outputs for 2-1 through 2-4 (horizontal top of garage). the other 2 were able to be left at 1 output. This doesn't make sense to me, but it was working.

Now, I just updated the firmware to V5. and set it up again using the additional outputs screen. Seems pretty straight forward on the setup, but I'm back to not working correctly and I can't just tell it to enable more outputs.

I'm attaching screenshots of the current setup, and a pick of what they are doing. The Right door is the only one working correctly on output 1-1. Am I doing something wrong?

PG1
Outputs
lights

11 Replies
Posts: 740
(@ezellner)
Prominent Member
Joined: 11 years ago

A few questions: Voltage? How are you power injecting (drawing or sketch would be good to see)? What's the distance between the controller and the data input to each string?
Also, on your first attachment page, on output 3-1, there is a "1" in the "Then Every" column and on output 4-1, "Rev" is checked. Neither of these is causing your issue but may confuse things later if they are not intentional. If your pixels were purchased this year, try changing the timing to 300 ns from 150 ns.


Reply
Posts: 1168
(@keith-r)
Noble Member
Joined: 19 years ago

I see a couple of possible issues here. If you are not power injecting, I doubt you can power 228 or 336 pixels from a single port. I never have powered more than 100 12v pixels from a single port. Less, if its 5 volts. You probably need to break up the strings and place on separate ports or power inject every 100 or so pixels.
If you are using the newer WS2811 pixels, the timing has changed, and you may need to up the timing as ezeliner says.
I also assume you are running a test pattern from the current set up. I would start with some more simple tests like only red or green, to insure the colors are correct.


Reply
Posts: 149
(@bob81354)
Estimable Member
Joined: 15 years ago

Hi
Have you tried starting the 2-1 to start at universe 2 ch. 175 and 3-1 to universe 4 ch 499 and so on and I would power inject that 144 for the 22 8and at 112 for the 336 and what sequence are you using make sure your good there


Reply
Posts: 6
Topic starter
(@thevolksman)
Active Member
Joined: 9 years ago
ezellner wrote:A few questions: Voltage? How are you power injecting (drawing or sketch would be good to see)? What's the distance between the controller and the data input to each string?
Also, on your first attachment page, on output 3-1, there is a "1" in the "Then Every" column and on output 4-1, "Rev" is checked. Neither of these is causing your issue but may confuse things later if they are not intentional. If your pixels were purchased this year, try changing the timing to 300 ns from 150 ns.

12V. Single power supply for all lights. Longest distance to controller for any of the strings is maybe 9'.

Now I see a few people stating power injection. I'm wondering why I was able to get it to work just fine (using V4) as is but only if I turned on more outputs but have nothing on those outputs. I would think that if it was a power injection problem I wouldn't get it to work no matter what I did. Does turning on additional outputs do something to the power output itself for the bank of 4 outputs?


Reply
Page 1 / 3
Share: