E682 Test Pattern a...
 
Notifications
Clear all

E682 Test Pattern after Firmware Upgrade

11 Posts
7 Users
0 Reactions
3,595 Views
Posts: 45
Topic starter
(@boknows)
Trusted Member
Joined: 11 years ago
[#43713]

Decided to upgrade a couple E682s that we had to the latest firmware. Afterwards we turned on a test pattern - green for the controller. Pixels lights as expected. Powered down controller and removed network cable. Powered controller back up and the pixels that were attached lit as green, but only for about 10 seconds and then turned off. Controller remained on. Plugged new set of pixels into different port and same thing - green for about 10 seconds and then nothing. Tested same pixels on a different brand controller and they worked as expected, so not a pixel problem. Would love to get the E682s working as expected. Any help would be greatly appreciated. BTW - same thing is happening on a different controller that we upgraded as well. So, not controller specific.


10 Replies
Posts: 376
(@k-state-fan)
Reputable Member
Joined: 16 years ago

Same thing when you change the test pattern.


Reply
Posts: 825
 DanJ
(@danj)
Prominent Member
Joined: 13 years ago

I haven't seen this particular activity on my E682s. I have 5.018 loaded on all of them.


Reply
Posts: 45
Topic starter
(@boknows)
Trusted Member
Joined: 11 years ago

Connected to the 682 today and changed the color in the test mode. Still same thin happens. Regardless what color I choose.

When connected to the controller and ok it's webpage. Set to test mode and it works. Disconnect the network cable - still works. Power the controller off and then back on the pixels light up for a out 10 seconds and then nothing.

Sent from my iPhone using Tapatalk


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
BoKnows wrote:Connected to the 682 today and changed the color in the test mode. Still same thin happens. Regardless what color I choose.

When connected to the controller and ok it's webpage. Set to test mode and it works. Disconnect the network cable - still works. Power the controller off and then back on the pixels light up for a out 10 seconds and then nothing.

Sent from my iPhone using Tapatalk

Why are you disconnecting the cable ?


Reply
Posts: 45
Topic starter
(@boknows)
Trusted Member
Joined: 11 years ago
angus40 wrote:Why are you disconnecting the cable ?

I disconnect it as I was setting the controller to be in test mode in the garage. It's not a part of a display or network. I just wanted to be able to power on the 682 and connect pixels and it sends them a test pattern. In this case - solid green.

In my normal display all of my controllers are connected to the network.

Sent from my iPhone using Tapatalk


Reply
Posts: 45
Topic starter
(@boknows)
Trusted Member
Joined: 11 years ago
BoKnows wrote:I disconnect it as I was setting the controller to be in test mode in the garage. It's not a part of a display or network. I just wanted to be able to power on the 682 and connect pixels and it sends them a test pattern. In this case - solid green.

In my normal display all of my controllers are connected to the network.

Sent from my iPhone using Tapatalk

Prior to upgrading the firmware we had the 682 set to test mode and could test our pixels once we installed them without any interaction with the controller. Just power it up. Connect pixels. Then it all worked. Just an easy way to test without anything else connected.

Sent from my iPhone using Tapatalk


Reply
Posts: 241
(@mrdudeman)
Reputable Member
Joined: 12 years ago

I haven't used v5 yet. but on v4 the controller test patterns are buggy especially if your using close to max channels.
took me hours to figure that out. now I always use test patterns from PC.


Reply
scott4864
Posts: 124
(@scott4864)
Estimable Member
Joined: 17 years ago

I think your problem is the entry on the setup page labeled "Timeout".

I changed it to 0 and the test pattern will remain on indefinitely now.


Reply
Posts: 1249
(@jstjohnz)
Noble Member
Joined: 17 years ago

That's interesting. It looks like TIMEOUT does still operate when a test pattern is enabled. That's a bug. The way timeout works is that there's a timer that's reset every time a packet is received. When that timer reaches the TIMEOUT value the data buffer is zeroed.

When you first power up the controller with a test pattern enabled, TIMEOUT seconds later the display will turn off. If you then change the test pattern to a different value it will stay on.

Thanks for catching that. Workaround. as stated, set timeout to 0.


Reply
Page 1 / 2
Share: