I am doing 12 RGB minitrees this year with star toppers (the medium-sized ones from Boscoyo). Each minitree is a 180 tree with 5 columns of 10 pixels, then I have each 20 pixel star topper wired in series with the minitree columns, for a total of 70 pixels per socket/output (see screen shot below). I have each minitree driven by one socket, setup to zigzag every 10 pixels. When I tried out a few of my sequences, the star topper doesn't look like I thought it should on effects like vertical/horizontal bars, etc; I think the zigzag every 10 pixels is impacting the response of the channels.... Should I drive the star toppers off of separate sockets that are not configured to zigzag? I am thinking maybe I should wire up all my minitree star toppers in series, with sequential non-zigzag channels, and that I should NOT have them wired in series with their minitrees' columns. Thanks in advance
you are using the zig zag because the tree strings go up then down and up then down? if this is so not having the stars wired off the tree and run the stars normal would work or if you are using vixen I know you have way too setup this without the zig zag on anything
Should have stated I am using xlights. Yes strings up then down etc. there is a specific star model in xlights so I am sure the xlights model is accurate for the physical star. I think I will try removing the zigzag and see if that makes the star look like I want it to look
Thanks for your replies
in xlights can you take a picture of the bottom left corner of the tree setup there you have the setup so you can tell the tree that it is zig zag tree and you wont have the problem of the board trying too zig zag the tree and star actually just looked an you have a odd number of strings on tree so wouldnt work for you in xlights
DanJ wrote:I am doing 12 RGB minitrees this year with star toppers (the medium-sized ones from Boscoyo). Each minitree is a 180 tree with 5 columns of 10 pixels, then I have each 20 pixel star topper wired in series with the minitree columns, for a total of 70 pixels per socket/output (see screen shot below). I have each minitree driven by one socket, setup to zigzag every 10 pixels. When I tried out a few of my sequences, the star topper doesn't look like I thought it should on effects like vertical/horizontal bars, etc; I think the zigzag every 10 pixels is impacting the response of the channels.... Should I drive the star toppers off of separate sockets that are not configured to zigzag? I am thinking maybe I should wire up all my minitree star toppers in series, with sequential non-zigzag channels, and that I should NOT have them wired in series with their minitrees' columns. Thanks in advance
Is your star physically wired to the end of the 50 nodes string? Just trying to visualize...
Sent from my iPhone using Tapatalk
that is what I think he has and doing a zig zag in the controller at 10 makes the star zig zag each 10 pixels so makes it not run right so he would have too rewire and put star by itself too be able too zig zag the tree in the controller
DMJPixel wrote:Is your star physically wired to the end of the 50 nodes string? Just trying to visualize...Sent from my iPhone using Tapatalk
TazChaLet wrote:that is what I think he has and doing a zig zag in the controller at 10 makes the star zig zag each 10 pixels so makes it not run right so he would have too rewire and put star by itself too be able too zig zag the tree in the controller
Thanks. I ask because I am building something similar and literally getting ready to solder in 9 pixels for a topper. Is it better to zigzag in xlights or controller? If you had to wire differently how would you do that? Thanks for the info - may help the OP too.
Sent from my iPhone using Tapatalk
now this is the thing it depends on what you actually have for a tree in xlights if you have a even number of strings you can setup the tree itself too zig zag but in his case his is only 5 legs on the tree so he cant do it in xlights and has too do it in the controler and havign the star attached causes a problem zig zagging thee port he is using for them
TazChaLet wrote:now this is the thing it depends on what you actually have for a tree in xlights if you have a even number of strings you can setup the tree itself too zig zag but in his case his is only 5 legs on the tree so he cant do it in xlights and has too do it in the controler and havign the star attached causes a problem zig zagging thee port he is using for them/div>
Thank you! So in looking at your channel counts your star must start at channel 901?
In my case I have one string of 100 nodes that have 10 nodes per strand (so 10 strands). If my topper is connected next in line that should work out ok - because I would have a topper model that would just start at the next channel after pixel 100...is that correct?
Thanks.
I think I see what you mean that an odd number of strings might cause issues.
yes the topper is the next channel in line after my tree my tree is channels 1-900 and the star is 901-984 the star has 28 pixels 84ch

