Dumb RGB Controller...
 
Notifications
Clear all

Dumb RGB Controller recommendations

5 Posts
3 Users
0 Reactions
3,255 Views
HydroWVU
Posts: 48
Topic starter
(@hydrowvu)
Trusted Member
Joined: 13 years ago
[#35359]

Good morning,

I am looking for a dumb RGB controller recommendations.

Currently I have:

1 LOR controller directly connected to the computer via USB.
2 Renard SS24's Connected to the Below bridge (each one connected in to its on port on e1.31)
1 E1.31 Bridge

Going to Add:

E6804 Running E1.31 for the Eves of my house.. 376 pixels
E680 (With UPG) with E1.31 Pixel Matrix 1024 pixels

I want to add 13 dumb RGB elements and two RGB Floods.

Here is what I was considering...

Option A) 1 or 2: 27 channel dmx controllers from Ray Wu or DMX controller connect to E1.31 bridge
Option B) 5: 3 channel dmx controllers... connected to E1.31 bridge
Option C) Renard DMX controller
Option D) Something I haven't thought of yet.

I have 4 other ports open on the e1.31 bridge. Here is where I need some help.

Can connect A or B directly to my e1.31 bridge by making the proper ethernet cables?
Can daisy chain 3 channel dmx controllers so I can minimize the wires going in to the e1.31?
Can I daisy chain a SS24 with a Renard DMX controller? This option is appealing because I can connect up all of my Renards. What are my options to drive something link these: http://www.aliexpress.com/store/product/Waterproof-RGB-LED-LED-Module-3-pcs-5050-SMD-RGB-LED-20pcs-a-string/701799_291745854.html

Oddly enough pixels were easier to plan out than dumb RGB's.

Thanks for the help.

John


4 Replies
Posts: 339
(@heldwhat-christmas)
Reputable Member
Joined: 15 years ago

I'm going to be connecting up just a few dumb RGB's up next year and I plan on using the extra ports I have on the Simple Renard RGB+w, mainly because I already have it and I'm not driving too many elements. I haven't tested it yet, but I'm already using it to control my floods. It could just get daisychained with your SS24's.


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

Your setup sounds a lot like mine but I have all E1.31
I have the 6 port bridge with the following connected to it:
LOR 16 channel controller running in DMX mode on port 1
2 X 27 channel ray WU DMX controllers off port 2
1 REN24DC and REN32 running on Port 6
I also have a pixel extender on Port 5 running my 8 candy canes (64 pixels) and a separate E682 for a 12 strip ray tree.
This setup simplifies things quite a bit as I have only one cable out to a 5 port switch and then the E682 and bridge connected to the switch.
Just one tip....
If you plan on running more than 5Meters of strip on 1RGB (3channels), then I would go with the REN24DC as it supports higher current, unless you mod the Ray Wu board to beef up the traces. I ran 5Meters on the Ray Wu board after the mod and things were fine, but I bought a REN24DC for the longer runs and use the Ray WU more for elements with a few modules like my coro stars.


Reply
HydroWVU
Posts: 48
Topic starter
(@hydrowvu)
Trusted Member
Joined: 13 years ago

Question about your LOR, I have noticed that by running it on USB it runs a little different than the rest of my channels. Running the LOR in DMX mode do you notice that? And how hard was it to switch over the LOR controller to DMX?

Thanks

John


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

Question about your LOR, I have noticed that by running it on USB it runs a little different than the rest of my channels. Running the LOR in DMX mode do you notice that? And how hard was it to switch over the LOR controller to DMX?

Thanks

No issues at all running in DMX.....all you have to do is make the crossover cable. I actually hard wired the cross over in the same enclosure using a rj45 Port and punch down and then ran a regular cat5 cable to the controller.
Now I only have one lol controller so the unit I'd is set to 1 (DMX 1 to 16). If you want to carry on to another lor controller you will need to change the lor I'd to 2 using the lor config utility which will give you DMX 17 to 32.


Reply
Share: