Do E682 test modes ...
 
Notifications
Clear all

Do E682 test modes respect "zig zag"?

8 Posts
3 Users
0 Reactions
3,842 Views
Posts: 485
Topic starter
(@jerry-rigs)
Honorable Member
Joined: 11 years ago
[#44183]

I am setting up a pixel tree 50 pixels tall with 16 strings around (12v ws2811 bullets)
My E682 (f/w v5.018) attaches to each string at the bottom.
I set the "First Zig" to 0 and "Then Every" to 50.

E682 1
E682 2

When I set the E682 test pattern to a chase, I expect to see the all the chases going up the tree. Instead I see the chases going up each string and then coming back down.
Is that the correct behavior?

I wanted to lock that down before setting up XLights.


7 Replies
Posts: 50
(@scott130377)
Trusted Member
Joined: 15 years ago

I have a similar setup and have the first zigzag set 50 and works fine

Sent from my SM-G935F using Tapatalk


Reply
Posts: 485
Topic starter
(@jerry-rigs)
Honorable Member
Joined: 11 years ago
scott130377 wrote:I have a similar setup and have the first zigzag set 50 and works fine

Sent from my SM-G935F using Tapatalk

What firmware version?

What is the difference between "first zig" = 50 and "then every" = 50?


Reply
gassy
Posts: 548
(@gassy)
Honorable Member
Joined: 17 years ago

from documentation:

The ZIGZAG feature has been enhanced in version 5. It is now possible to specify 2 zigzag lengths. The first specifies the
length of the FIRST zigzag segment, the other specifies the length of all other zigzag segments. This allows the use of the
ZIGZAG function on an array where the dimension of the array doesn’t divide evenly into the length of the pixel strings.


Reply
Posts: 485
Topic starter
(@jerry-rigs)
Honorable Member
Joined: 11 years ago
gassy wrote:from documentation:

The ZIGZAG feature has been enhanced in version 5. It is now possible to specify 2 zigzag lengths. The first specifies the
length of the FIRST zigzag segment, the other specifies the length of all other zigzag segments. This allows the use of the
ZIGZAG function on an array where the dimension of the array doesn’t divide evenly into the length of the pixel strings.

I don't think that answers the question.
Given a string of 100 pixels, is there any difference between:
"first zig" = 50, "then every" = 0
and
"first zig" = 0, "then every" = 50

RTFM is always a good answer (and I did).

In this case, ZigZag is not working as documented. I am troubleshooting between various versions of E682 firmware, and XLights.


Reply
gassy
Posts: 548
(@gassy)
Honorable Member
Joined: 17 years ago

I believe you have to have a value other than 0 in the 'first zig' before any value in the 'then every' is executed. But then again, that's just my thinking.


Reply
Posts: 50
(@scott130377)
Trusted Member
Joined: 15 years ago
Jerry-Rigs wrote:What firmware version?

What is the difference between "first zig" = 50 and "then every" = 50?

I am using firmware 5.018. You have to think of it as first zag after 50 then every 50

Sent from my SM-G935F using Tapatalk


Reply
Posts: 485
Topic starter
(@jerry-rigs)
Honorable Member
Joined: 11 years ago

I started this thread because I was couldn't get zig-zag to work on my E682 with v5.018 firmware. Even the E682 test patterns were not zig-zagging. Running tests from XLights didn't help either. I tried a number of "equivalent" configurations: 8 universes of 100 pixels (300 channels) each then 5 packed universes using all channels in the universe before spanning to the next. I found a couple hardware connection errors and a few bad crimps but I couldn't get the zig-zags working. The errors were all over the place. At one point, I was getting "sequence errors" equal to half the "packet count" on one universe.

I back-leveled to v4.078-01 and was able to get zig-zags working. But I -like- v5 so upgraded to v5.023-01 and went through the exercise again with similar but different failures.

After many hours struggling with this, I am convinced that v5.xxx of the E682 firmware is not behaving for me. If it would help the dev, I am willing to run diagnostics.

I back leveled to v4.078-01 and everything I want to do is working.

In my frustration, I was crabby with those trying to help me. I am sorry.


Reply
Share: