I have an electronics questions for a non-Christmas related project, where I basically need to have two LED strips to show the same. Is there a recommended best practice for connecting two strips/strings to one controller output? Maybe a non-inverting buffer like a CD4050B? The microcontroller data output would be connected to two of the inputs...
Thanks!
Depends on how far you need to drive the signal. Simplest may be to put a pair of pixel drivers (Famp, Null pixel etc.) near the controller and let those devices drive the rest of the string.
From what you're saying, if the distance is short (which it will be, probably IRO 30cm to each of the two strips) technically there should be no problems connecting the same signal to both strips rather than daisy-chaining them? I could of course test this but I don't have the strip yet... Output will be from an ESP32 via a 3.3->5V level shifter. Actually thinking about it two 'channels' on the level shifter may be the way to go.
RichieNorthcott wrote:
From what you're saying, if the distance is short (which it will be, probably IRO 30cm to each of the two strips) technically there should be no problems connecting the same signal to both strips rather than daisy-chaining them? I could of course test this but I don't have the strip yet... Output will be from an ESP32 via a 3.3->5V level shifter. Actually thinking about it two 'channels' on the level shifter may be the way to go.
Yes this will work
Unless your somehow maxing out your controller, both WLED and ESPixelStick will allow you to mirror output pins.
On a standard ESP32 ESPixelStick officially supports 6 pixel outputs. That doesn't necessarily mean six is a hardware limit—it may simply be where Martin decided the firmware was mature, reliable, and maintainable. I was able to get 16 outputs working with 42 pixel strings on an ESP32-WROOM-32S under WLED at about 43 FPS.
ErnieHorning wrote:
Unless your somehow maxing out your controller, both WLED and ESPixelStick will allow you to mirror output pins.On a standard ESP32 ESPixelStick officially supports 6 pixel outputs. That doesn't necessarily mean six is a hardware limit—it may simply be where Martin decided the firmware was mature, reliable, and maintainable. I was able to get 16 outputs working with 42 pixel strings on an ESP32-WROOM-32S under WLED at about 43 FPS.
There are a few platforms where the ESPS V4 is running 8 output ports. 🙂
They have firework lights made out of digital strip where a single strip goes up, and then the firework spokes out 6 or 8 directions. I would presume all the data pins on those spokes are tied together as they all do the same thing.
Back when I made a mistake and made all of my 10x10 matrix candy canes without and output and a way to chain them in series, I looked at using an ESP32 to run 10 canes in a single row off of 10 outputs. It worked and I found that a cane still worked flawlessly with 24 feet of wire. I didn't try to see how many could run on a single port.
Realize that just because it may work with multiple loads, it could be over the designed out put current. Works today, burns out tomorrow.
Thanks for the advice. Yes I simply connected two strips to one output and it's working fine. The distance to each strep from the controller is about 20cm max. If you're curious it's LED effects on the LHS and RHS of a mini 10 pin bowling lane.
RichieNorthcott wrote:
From what you're saying, if the distance is short (which it will be, probably IRO 30cm to each of the two strips) technically there should be no problems connecting the same signal to both strips rather than daisy-chaining them? I could of course test this but I don't have the strip yet... Output will be from an ESP32 via a 3.3->5V level shifter. Actually thinking about it two 'channels' on the level shifter may be the way to go.
I would recommend adding a 220 Ω resistor per strip on the data line, placed right at each strip’s input — and with short runs (around 30 cm) and a proper 3.3→5 V level shifter, this setup will give you stable, reliable signaling even when driving both strips in parallel.
