Notifications
Clear all

Bad pixel

26 Posts
12 Users
0 Reactions
4,869 Views
Posts: 215
Topic starter
(@jdesign21)
Reputable Member
Joined: 13 years ago
[#56566]

So 3 years ago I purchase 2 different types of customs pixels from ray wu. Last year and this year I been dealing with tons of bad pixels. I'm tired of troubleshooting, cutting and replacing bad pixels. I decide to call them a lost and trash them. Since I want to replace them I'm looking to see if there is another vendor that does custom pixels sizes? I don't want to order them ray wu again.


25 Replies
MartinMueller2003
Posts: 7612
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I also purchased 2000 pixels from Ray Wu at about that the same time and had to spend time every day fixing the strings. I thought it was PSUs, nope. Wiring, nope. I finally pulled them out of the show and replaced them. Just about ANY vendor would give you getter results.
I went to ebay and purchased 2000 of these: https://www.ebay.com/itm/164693553277?mkevt=1&mkpid=0&emsid=e11051.m43.l1123&mkcid=7&ch=osgood&euid=06f1b5ad68a248499516f7c337705c17&bu=42954339803&osub=-1%7E1&crd=20221027201452&segname=11051

After my initial shock that they had marked the arrow in the opposite direction of all of my other strings, I tested and deployed them. I have had 1 pixel out of the 2000 pixels fail in the past three months of daily testing and display. I am not seeing any other issues with them so far. We will see how the hold up over the summer in the shed.


Reply
Posts: 418
(@richienorthcott)
Reputable Member
Joined: 7 years ago

I have an issue with specific pixels in my display this year. The only common pattern I'm seeing is:

1. I know they were bought at the same time from the same vendor
2. They are the furthest from the controller, so stand the highest risk of having considerably less than 5V.
3. They are mounted with the pixel heads facing towards the sky. The weather has been shocking this year, they were covered in snow and ice for a week and now everything is damp as we have constant drizzle.
4. They have all seen a similar amount of usage (not much in the big scheme of things)
5. The longer I leave them 'on' running a R/G/B/W solid colour sequence (at 40% power) the more problems seem to appear.

Generally I'm seeing the blue LED fail (so white = yellow) and noise (flicker) in the data line from a certain pixel onwards. Chopping out and replacing the offending pixel generally fixes things.

It might just be the damp air getting inside some of them, but is it possible for pixels to fail because of having an under-voltage? All my pixels run from the same PSU, I have no issues with any of the other sections of the display - it's super frustrating.

Can a lower voltage cause permanent damage? Seems unlikely - and I'm not maxing out the pixels since I run them at 40% (channel values 102,102,102 for White)


Reply
MartinMueller2003
Posts: 7612
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

A lower voltage can NOT cause damage to a pixel or the LEDs attached to it. It can cause discoloring and flickering but those will go away when the voltage comes back up.


Reply
Posts: 418
(@richienorthcott)
Reputable Member
Joined: 7 years ago

Thanks for confirming - the obvious suggestion would be to measure the voltage, but everything is sealed up so tricky. I think the rain may be a factor too, although in theory everything is water tight, I'm sure moisture finds its way in. In particular the waterproof automotive connectors I use are starting to give me issues now in their 4th year. If I was to do it again I'd buy moulded connectors and solder/heatshrink the tails.


Reply
Page 1 / 6
Share: