2 inch 2811 questio...
 
Notifications
Clear all

2 inch 2811 question

11 Posts
6 Users
0 Reactions
3,707 Views
Posts: 89
Topic starter
(@musicman72)
Estimable Member
Joined: 9 years ago
[#53029]

I'm looking all over for some 2 in spaced 2811 pixels. All I can find in 3 and 4 inch. Do you have to cut and make your own 2 inch spaced pixel strings? I'm looking to redo my mega tree and looking at 2 inch spacing for that prop. Also I am using Renard PX1 boards. Am I reading the wiki correctly that each board can only run 200 pixels?
Thanks in advance guys!

Sent from my SM-N975U using Tapatalk


10 Replies
Posts: 236
(@afremont)
Reputable Member
Joined: 10 years ago

If you want 2" spacing using the actual power and data wires, then it would be easier to zip tie the extra wire, rather than cut and solder. That said, I prefer using the plastic 1" wide strips with holes for plugging in bullet or square pixel strings. Much easier.

Sent from my moto g(7) using Tapatalk


Reply
Posts: 89
Topic starter
(@musicman72)
Estimable Member
Joined: 9 years ago

Thanks! I will look up some videos on pixel mega tree construction. I hadn't thought about adding a frame. That makes sense though.we are just beginning our ac to pixel conversion. So this is a learning curve for us. Definitely wanna do it right for years of future enjoyment

Sent from my SM-N975U using Tapatalk


Reply
Posts: 89
Topic starter
(@musicman72)
Estimable Member
Joined: 9 years ago

What other pixel boards should I be looking at? We are running vixen off of our laptop with an all Renard data cord system. I havent invested in a raspberry pi yet as I wasn't planning on starting my conversion next year. I believe I will use my px1's for my windows as this will be a lower pixel count and simple square pvc construction. There will be approximately 50-100 pixels per window. Im not familiar with board construction and soldering. So I will need to purchase boards pre made.

Sent from my SM-N975U using Tapatalk


Reply
TomL8345
Posts: 1356
(@toml8345)
Noble Member
Joined: 15 years ago

You can't go wrong with a Falcon controller. They are Rock solid and have lots of support on the forums. There are several others out there as well. I would recommend that you stay away from Pixel Strips and stay with Nodes. TheBoscoyo Mounting Strips are exactly what you want for your prop. You will have a couple of options for running both the Pixel Controller and Renards together. And make the jump to the RasPi and FPP. They are worth the effort to learn.


Reply
Posts: 89
Topic starter
(@musicman72)
Estimable Member
Joined: 9 years ago

How many pixels can you run off of a falcon?

Sent from my SM-N975U using Tapatalk


Reply
TomL8345
Posts: 1356
(@toml8345)
Noble Member
Joined: 15 years ago

Here is a breakdown from the linked falcon site. You might also want to go to the Falcon Forum


Reply
TomsLEDs
Posts: 444
(@tomsleds)
Honorable Member
Joined: 7 years ago

My RS Pi-4 / Sandevices e682 combo (1st board) is current running 2,006 pixels in 12 universes. That's about 97% maxed out.


Reply
Posts: 47
(@mikeni)
Trusted Member
Joined: 11 years ago
TomsLEDs wrote:My RS Pi-4 / Sandevices e682 combo (1st board) is current running 2,006 pixels in 12 universes. That's about 97% maxed out.

I just ordered a RS Pi-3B+.. I've never used this little computer before. Will it manage a basic light show that runs two Sandevices E682's? I'm not exactly expert level with my light show, but the kids and neighbors love it...

Sent from my Pixel 4 XL using Tapatalk


Reply
TomsLEDs
Posts: 444
(@tomsleds)
Honorable Member
Joined: 7 years ago

That should not be a problem. Just have to set it up for Falcon Player. I have 2 san device cards as well, but no time to use both this year. Going live in 3 days.


Reply
Page 1 / 2
Share: