12v Pixel Wiring
 
Notifications
Clear all

12v Pixel Wiring

12 Posts
4 Users
0 Reactions
2,399 Views
Posts: 17
Topic starter
(@thehappygrizzly)
Eminent Member
Joined: 3 years ago
[#57295]

Ok... I officially feel stupid. I wanted to quickly test my 12v seed pixels ( https://wallyslights.com/collections/12v-pixels/products/12v-ws2811-200ct-seed-pixels-strand ) and tried to make a quick jumper wire setup. After poking around the web for a little, I decided to just use my Arduino with FastLED to turn all the lights to white. I sent the ground jumper wire inside of the xConnect female end to one of the Arduino gnd pins to quickly connect the two wires. The gnd pin next to it is hooked up to my 12v power supply. The 12v line is connected directly to the power supply. There is power on the male end of the strand.

I made a diagram if that doesn't make sense. The battery represents the 12v supply and the LED strip is the seed pixels.

I'm sure I made an obvious error, but does anyone know what that might be? Is there a way to quickly test a strand of 12v pixels with jumper wires?

Thank you for your help in advance.

Screenshot 2023 11 17 165757

11 Replies
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

You dont show power V+/Vin to the Arduino !


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Here is a power scheme ------> https://forum.arduino.cc/t/powering-uno-via-vin-pin-12v-dc-wall-adapter/686071

Fusing the Vin may be required to protect the Arduino .


Reply
Posts: 17
Topic starter
(@thehappygrizzly)
Eminent Member
Joined: 3 years ago

The Arduino is being supplied 5V via the printer cable/usb.


Reply
Posts: 1420
(@1pet2-9)
Noble Member
Joined: 6 years ago

What I found easier was to give the Arduino 12V via the barrel jack, and then connect the Vin pin to the LED strip. It gets really hot, but I ran it all night in the dead of summer and it didn't skip a beat.


Reply
Posts: 17
Topic starter
(@thehappygrizzly)
Eminent Member
Joined: 3 years ago

Found the issue! These lights seem to be interesting in the fact that the male end is the controller end. After tinkering around for a while, I was about to give up but tried using the opposite end for the data, and what do you know? I guess the male end is the controller end for these lights! Thanks for everyone's suggestions as well!


Reply
Posts: 1420
(@1pet2-9)
Noble Member
Joined: 6 years ago

Your seeds have "ends"? All I have are 3 wires and I have to figure out how to put a connector on it.


Reply
Posts: 17
Topic starter
(@thehappygrizzly)
Eminent Member
Joined: 3 years ago
1pet2_9 wrote:Your seeds have "ends"? All I have are 3 wires and I have to figure out how to put a connector on it.

Yea, I linked the ones I got in my first post. They came with xConnect ends already installed, which was why I opted for them. 12V was nice, and the preinstalled connectors should in theory bring a quick and easy install for my first year. Famous last words!


Reply
Posts: 418
(@richienorthcott)
Reputable Member
Joined: 7 years ago

On most pixels and strip that I have purchased the female connector is on the input, which seems illogical to me.

When I fit my own waterproof plugs I use female on the controller outputs and male on thel connections to pixels. Normally on pixels the data in wire is to the side of the PCB the WS2811 chip is on.

You can power your arduino and pixel however you wish, but make sure the grounds are connected together. It's also prudent to fuse the pixel 12V line.


Reply
Posts: 1420
(@1pet2-9)
Noble Member
Joined: 6 years ago

Maybe the guy soldering on the Xconnects onto the seeds doesn't have an electron microscope to figure out which direction they are going. He has a 50/50 chance. 🙂


Reply
Page 1 / 2
Share: