Network Setup
 
Notifications
Clear all

Network Setup

11 Posts
6 Users
0 Reactions
4,974 Views
Posts: 79
Topic starter
(@slim00209)
Estimable Member
Joined: 13 years ago
[#45610]

Good afternoon,

As we get later into the year, I am finally getting to the point where I should start to think about setting up my controllers on a network. This is my biggest concern with this being my first year with something other than AC controllers. First off, I will explain the details of my setup. I will be running approximately 4500-5000ish 12v ws2811 pixels. The hardware consist of 1 Falcon F16v2 with a 16 port expansion board, two Raspberry Pi 3's with Falcon Picap and a BBB with octoscroller running a 2x3 P10 panel. I can add a third Pi if needed to run the show if one with the Picap will not. Here is where I get lost. How exactly do I get the all the controllers to talk to each other. I understand that I will need a network switch and they will all be connected via Ethernet through the switch. 1. Do the controllers or switch have to be connected to my home router if I use the supplied batteries to power the Picap for the RTC? My only concern with this is accessing FPP if i needed to make a change. 2. I have watched several videos where people set IP's of the controllers to 10.10.10.x. Is this something that can be done given that it is not connected to the internet? I may be way out in left field but my understanding is that, for example, Master Pi would be 10.10.10.1, second Pi, 10.10.10.2 and so on. I will also need to figure out how to configure the Pi's and controller with the Master and slave but I'm sure there is literature on that somewhere around here and I will try to find it. Can someone point me to a good video or website that will assist me with setting up? I apologize if this has been laid out before. My search did not yield anything. Any help is much appreciated.

Thank you,
Ryan


10 Replies
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

There are many ways to connect these and I know others will chime in. We run a show with several locations and none of them are connected to the Internet. The only time you need that connection (to the Internet) is to upgrade firmware that may not be available to download. Once everything is up to the level you want, disconnect (if you want).


Reply
Posts: 116
(@studiopro)
Estimable Member
Joined: 12 years ago

One possibility is to use a second home router downstream of yours. If you have an older one this wouldn't even cost anything extra. Plug the Internet/WAN port on second (light show router) to one of the computer ports. If your main router is 192.168.1.1 set up the second as 192.168.0.1 or vice versa. You can then set up your controllers/pi's etc to 192.168.0.X. I am a big fan DHCP reservations in the router, or you can set up static addresses for each device

If you need to access your light show network you can plug in, or hop on that wi-fi. You can also set up port forwarding to any of your equipment and access it from your home network without changing wi-fi or anything. This setup would also allow time to work on your light show network and still keep the traffic split. If you want more details or have questions feel free to ask and I can go in more depth.


Reply
Posts: 79
Topic starter
(@slim00209)
Estimable Member
Joined: 13 years ago

Thank you. Any recommendations on a wireless bridge or access point that would allow me to connect to my router without actually running a physical wire? And then run Ethernet to the controllers?

Sent from my iPhone using Tapatalk


Reply
MartinMueller2003
Posts: 7612
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

A media bridge (sometimes called a WiFi repeater) would allow a wireless connection to your home network and then create a wireless network on which your show can run. Many of the newer access points support a bridge or repeater mode. Depending on what you buy, it could also have ports on it that you can plug your controllers and such into.


Reply
Page 1 / 3
Share: