DISPOSABLE CAMERA F...
 
Notifications
Clear all

DISPOSABLE CAMERA FLASH CONTROL

44 Posts
18 Users
0 Reactions
21.9 K Views
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago
[#75]

I wanted to use strobes in my display but the cost is quite high even for curtain strobes. I bought a load of disposable flash tubes and went to build a power supply/trigger but the cost was way too high for the componets.

I pulled the strobe out of a disposable camera and found a way to trigger it. With the circuit below, I can trigger it from Vixen several times a second.

I have found these cameras for as low as $1.95 with free shipping. Resell the film and batteries (AA size) and make some of the money back. I am also going to check and see if I can purchase used cameras.

I am planning to purchase a bunch of these cameras, tear out the strobes, and build a honker 300 VDC power supply.

The circuit below is just for one strobe so each strobe would need an 800 ohm resistor (or higher value for longer charge times or lower value for shorter charge times).

Steps:
*Remove the strobe from the disposable camera
*Toss the battery
*Connect SW2 to the SCR
*Connect the SCR to triac driver (in your SSR)
*Connect the 300 VDC power supply (with charge limiting resistor) across the large capacitor
*Trigger it with Vixen

The 800 ohm resistor heats up if you flash frequently.

Here is what it looks like after you remove it from the camers (without the battery).


43 Replies
Posts: 274
 Matt
(@matt)
Reputable Member
Joined: 19 years ago

Cool!

What kind of camera? Is it the disposable type you can get at Walgreens or something else?

How long do the flash bulbs last? Do they blow out after so many flashes?

-Matt


Reply
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago

I am sure any disposable camera would work. They all look about the same and even the button for charging the capacitor is in the same place. Go to Walgreens and see if they will sell you the old ones that have been turned in. You only want the circuit board. The case might make a nice enclosure with some silicone sealer or latex caulking.

I have not tested how many flashes it will go but that is on the list.

I would search eBay for "disposable camera" and there are lots of hits. They sell them in lots of 10, 15, 20, and 25. The shipping is quite high but the price is about as good as it gets.

These guys might sell them at a low price.


Reply
Posts: 101
 Zane
(@zane)
Estimable Member
Joined: 19 years ago
FireGod wrote:The shipping is quite high but the price is about as good as it gets.

hmm not to be wise but i went to the site and right at the top it said free shipping 😆

20140129 084422 resized
20140129 084550 resized
vltd
1228111129
Chris 2014

Reply
Macrosill
Posts: 9739
(@macrosill)
Member
Joined: 20 years ago

I believe the shipping statement was pointed towards the Ebay sellers.


Reply
Posts: 101
 Zane
(@zane)
Estimable Member
Joined: 19 years ago

I just realized that they where based out of my city 😆 maybe i could pick them up somewhere in town and send them to people.


Reply
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago

I used a 120/220 volt transformer for testing but when I build a LARGE power supply, I'll just pull 220VAC directly from my breaker box.

A fuse, few big diodes for a full wave rectifier, and a couple of huge 450volt capacitors (from eBay) should do the trick.

Edit: I'll probably do a two stage charging circuit. One slow one with a limiting resistor to get the caps up to a reasonable voltage and a second one without current limitng to maintain the voltage.


Reply
Posts: 274
 Matt
(@matt)
Reputable Member
Joined: 19 years ago

Let us know how it goes with those monster diodes and caps!

-Matt


Reply
Posts: 18
 buck
(@buck)
Eminent Member
Joined: 19 years ago
Reply
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago

If I buy just the bare boards like Buck found, any ideas for weather proofing?

My first thought was to mount the SCR and charge limiting resistor on the board, solder the four wire leads to the board, then get a gallon of fiberglass resin and hardener from AutoZone (or whereever) and coat the entire thing except the lens. Either paint it on, dip it, make a cheap mold, or just pour it over both sides of the board.

Remember, the flash is started with a 4000 volt pulse and the capacitor is at 300 volts so it is importaint that it stay dry.

Thoughts?

20151121 110646 resized
Christmas2015 8
Christmas2015 9

Reply
Page 1 / 5
Share: