Desoldering Techniq...
 
Notifications
Clear all

Desoldering Techniques

30 Posts
12 Users
1 Reactions
2,716 Views
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

This is my soldering station.
This is my Desoldering station.

I have had them both for well over a decade and they are both going strong.


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

I second Yihua, had mine since 2012 and other than replacing a heating element still works fine.
I did opt to go for this one this year: Yihua T12
Purely because I wanted more airflow to fix PS5 HDMI ports. My old station used a small fan in the handle and was not producing reliable heat and good airflow, this one has a pump in the unit. I just unboxed it (xmas present), so I can't say if it is significantly better yet.


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I have replaced the heating element on the soldering pen once. That is on par with my Weller solder station.


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

The best desoldering station I've ever used was an old Weller pen that used compressed air to create a venturi effect. We used house air that was at 100PSI. Those holes looked like they'd never been soldered. Heat, wriggle the pin in a circle and apply vacuum. Wish I had that ability still.


Reply
Posts: 2216
(@ctmal)
Famed Member
Joined: 19 years ago

I have thought about getting a desoldering station but the few times I would need to use it I never feel like waiting.
I've found solder wick works great if you put flux on it before you use it. Most times I can get a nice clean removal. If not, I just load it back up with solder and do it again.


Reply
Posts: 849
Topic starter
(@tfischer)
Prominent Member
Joined: 17 years ago

That's so counter-intuitive to me lol. I was watching a video on desoldering the other day where he kept doing that... he'd desolder, have the tiniest bit left, and be like "well we need to try again" and then added a ton of new solder. In my mind, it's like "oops, I missed a spot vacuuming, let's track in some more mud!" lol


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

It's like the old "prime the pump" saying for water pumps, you need enough solder to pull a vacuum through the hole and enough mass to keep it going. A good cleaning and a bit of silicone spray can do wonders for those suckers too. Before Solder Wick, I actually wore out the internal rubber ring gasket multiple times in a production setting.

If given the choice, I'd rather use a real desoldering iron though. But, I can still use the "get 'er done" sucker method.

If you need to add flux to solder wick, it's time to toss it and get a new one. I've done it with old wick (cheap wick) or just braided wire when I had to, but there is good and bad wick. There's also, "you get what you pay for" wick. Real Solder Wick brand always works, cheap stuff, sometimes not.


Reply
rayhjr
Posts: 972
(@rayhjr)
Noble Member
Joined: 12 years ago

I just ordered these.
YIHUA 853AAA 1200W Soldering Station
YIHUA 2 in 1 Desoldering Station
There are some coupons avable. Hopefully these will last me into retirement, LOL. https://www.aliexpress.us/item/3256809817207703.html?spm=a2g0o.order_list.order_list_main.4.2cc91802HO2LkC&gatewayAdapt=glo2usa

Solder

Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

I don't unsolder anymore.


Reply
Posts: 849
Topic starter
(@tfischer)
Prominent Member
Joined: 17 years ago

YIHUA was what I was looking at but just couldn't justify it for the tiny amount I actually desolder.

My project that needed the desoldering ended up not being a success. But I was able to source a new board for free.


Reply
Page 2 / 3
Share: