Desoldering Techniq...
 
Notifications
Clear all

Desoldering Techniques

30 Posts
12 Users
1 Reactions
2,717 Views
Posts: 849
Topic starter
(@tfischer)
Prominent Member
Joined: 17 years ago
[#59042]

How do you all get desoldering done? It's always been one of my least favorite electronics things to do.

I've tried:
1) A desoldering iron I've had since I was a kid from Radio Shack. It's like a regular soldering iron, except it has a hollow tip and a bulb thing you're supposed to squeeze, heat up the solder, and let it suck it out. It kinda, sorta, but not really works. I've found it's too clunky for most modern board work and runs hot enough to cause board damage.

2) A standard spring-loaded solder sucker. I've found it too hit/miss as well. Seems that no matter how quick I try to be, the solder firms up too much before it sucks.

3) Desoldering wick. Again, I've found it hit/miss.

Most of the time I can get components with 2-3 legs done. But if I need to do something more complicated, it will remain frozen to the board.

Today I tried to remove an RJ-45 jack on a Falcon distribution board. Couldn't get it to budge. And I couldn't find my desolder braid which I think would have been the best of the three tools for the job. And I can't 'cheat' by cutting off the component legs and doing them one by one.

I'd love to buy one of the vacuum desoldering tools with the electric pump, but can't justify it for the little bit I do. Amazon has a version that's kind of a combo of my #1 and #2 above (soldering iron with built in solder sucker) but I'm not convinced that's worth the $36 they're asking either.

So school me, oh electronics gurus...


29 Replies
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

I have a real desoldering station I bought when all of the methods you described failed me. Having a temp control, tips with different sized holes and a real pump on a trigger makes all the difference.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

I've had pretty good luck using my hot air soldering station to loosen the parts.


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
dirknerkle wrote:
I've had pretty good luck using my hot air soldering station to loosen the parts.

That works well getting the parts off. Nothing like a vacuum pump to get those hole squeaky clean 🙂


Reply
rstehle
Posts: 4348
(@rstehle)
Illustrious Member
Joined: 19 years ago

I've always only used the solder sucker. Sometimes you need to add a bit of solder to get them to work well. Agreed that the one Martin describes is the best bet if you are going to do more than a piece or two.


Reply
ChiefWarrant
Posts: 570
(@chiefwarrant)
Honorable Member
Joined: 19 years ago
rstehle wrote:
I've always only used the solder sucker. Sometimes you need to add a bit of solder to get them to work well. Agreed that the one Martin describes is the best bet if you are going to do more than a piece or two.

Same here....solder station, with tempreture control and a sucker. As @MartinMueller2003 points out, if you are replacing a part, then you wnant the hole squeaky clean.

The biggest thing I wish i have is a thrid hand, so often i am also using clamps and locking forceps.


Reply
rayhjr
Posts: 972
(@rayhjr)
Noble Member
Joined: 12 years ago

I do, dearly love, to solder. I somehow missed my calling, LOL!
I have a spring loaded sucker and braid on hand. I tried one of those cheap plug in vacuum suckers off Ali and it was just that, Cheap.
It only lasted a few sessions and was done. I wish I had invested in a good desoldering station (like Martin talked about) when I got started some years ago, And I still might. Hard to justify the cost, compared to how much I'll use it. One of those specialized tools that you need it when you need it, and that is only every now and then.
I have lifted a few pads in my time also. Ground pins are the hardest to get out/clean, for me. Depends on if I am trying to save the part or just get it out, as to how much heat I can apply. I try to get it out, them clean it up. Notice I said, TRY.


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

I used the old "solder sucker" for years and found it hit or miss as well.
I have since purchased one of these when it was on sale for 20$.

solder sucker

It Heats up quick and just place over hole and press. So far so good!


Reply
Posts: 849
Topic starter
(@tfischer)
Prominent Member
Joined: 17 years ago
DrNeutron wrote:
I used the old "solder sucker" for years and found it hit or miss as well.
I have since purchased one of these when it was on sale for 20$.

It Heats up quick and just place over hole and press. So far so good!

That's the one I alluded to at the end of my OP where I said "I'm not sure it's worth the $36 or not". Sounds like you say it is, and that's good to know!


Reply
rayhjr
Posts: 972
(@rayhjr)
Noble Member
Joined: 12 years ago
MartinMueller2003 wrote:
I have a real desoldering station I bought when all of the methods you described failed me. Having a temp control, tips with different sized holes and a real pump on a trigger makes all the difference.

So, if someone was to make the investment in one of these, what should someone look for in a good station? Brands? Are you satisfied with your station? Would you do anything different if you had to do it again? Inquiry minds want to know, or at least I do.


Reply
Page 1 / 3
Share: