xlights sends out w...
 
Notifications
Clear all

xlights sends out wrong data to pixels.

22 Posts
3 Users
0 Reactions
9,770 Views
Posts: 39
 jssr
Topic starter
(@jssr)
Eminent Member
Joined: 5 years ago

Oh, I scared everyone.
But it doesn't matter, the project is canceled because there is no more time. Wish everyone a Merry Christmas. Greetings Jörg


Reply
Posts: 39
 jssr
Topic starter
(@jssr)
Eminent Member
Joined: 5 years ago

Hello Mike, thank you for your feedback. I can try again, maybe something will change.
The orange data cable goes in at the beginning and if I understand it correctly it goes from module to module until I connect the two data cables (blue). From then on the organ ends. Or can also be connected together at the beginning with data cables. IM not sure.

The orange data cable is routed from module to module via the yellow / green cable. Arch on the left, Christmas tree, candy cane, snowflake, star base, star, star, snowflake, star and to the arch on the right.

I haven't paid much attention to the data speed until now. But there could be something to it, when you take a quick look, neither the screen display nor the lights follow. This is the case, for example, with Do They Know lt's Christmas for short periods.
Thank you Mike, I'll report if anything changes. Greetings Jörg


Reply
Posts: 39
 jssr
Topic starter
(@jssr)
Eminent Member
Joined: 5 years ago

With xlights, only a maximum of 1000 channels can be set. At least with a generic serial. Where do I then enter the missing channels from 875?


Reply
Posts: 39
 jssr
Topic starter
(@jssr)
Eminent Member
Joined: 5 years ago

I just changed the data. Unfortunately nothing changes about the fact that the fir tree does not shine alone. Other areas always shine with the same number of pixels.

25

26

The following error is entered in the check sequence. From the star with the foot onwards, the models have no controller assignment. But somehow I can't assign them because I can set over 1000 channels.

28

Under the controller settings under Models you can see the modules are missing.
Question: How do I get it that I can assign the missing modules to the Teennsy when I can only enter 1000 channels. Somehow I have to tell xlights that from pixels ?? the second data cable is to be used. And where do I have to connect the second data cable. From the pixel or directly to the beginning of the modules.

27

The three pixels also shine unchanged in white

23

Reply
Posts: 39
 jssr
Topic starter
(@jssr)
Eminent Member
Joined: 5 years ago

Hello, does anyone have any idea how I could assign the channels over 1000. I have no more ideas how to get it going.
Greetings Jörg


Reply
Posts: 39
 jssr
Topic starter
(@jssr)
Eminent Member
Joined: 5 years ago

Hi Mike,
I've tried other settings like DMX, but nothing happens.
Thank you very much for your effort, but the lighting is over for this Christmas.
Have a nice christmas


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
jssr wrote:With xlights, only a maximum of 1000 channels can be set. At least with a generic serial. Where do I then enter the missing channels from 875?

ESPixelStick V4 will output up to 3600 channels on the ESP8266 and 9000 channels on the ESP32. WARNING: At the data transfer rates used by most generic serial devices, this amounts to a multi second refresh rate (as in 1 or less frames per second).

At 120Kbps data rates you get the following refresh rate for 1000 channels:

120000 bits per second data transfer rate.
8 bits of data plus two overhead bits = 10 bits per channel
120000 / 10 = 12000 data bytes per second
1000 channels = 12 frames per second

Most of us run our shows at 20fps or 40fps. That makes 1000 channels on a generic serial line a less than good design choice.


Reply
Posts: 423
(@keithsw1111)
Reputable Member
Joined: 11 years ago

.39 now supports 4096 channels of generic serial

Sent from my iPhone using Tapatalk


Reply
Posts: 39
 jssr
Topic starter
(@jssr)
Eminent Member
Joined: 5 years ago

4096 could help me get my 1875 working.
On my laptop he just showed me that there is a new version. Is a very fresh version.
Will test it tomorrow evening. It's almost midnight here now.
In any case, thanks for the info. Will report if it works now.


Reply
Posts: 39
 jssr
Topic starter
(@jssr)
Eminent Member
Joined: 5 years ago

Hello Mike, that was the message I was desperately looking for. It finally works with the channel expansion. Now I can set up the lighting a few days later and hope that no further problems arise.
But I don't want to forget to thank everyone. Without your help and support, I would not have made it.
When everything is set up I'll make a video. Jörg


Reply
Page 2 / 3
Share: