xLights 4.0 Status
 
Notifications
Clear all

xLights 4.0 Status

34 Posts
16 Users
0 Reactions
18.1 K Views
smeighan
Posts: 2595
Topic starter
(@smeighan)
Famed Member
Joined: 15 years ago

I think i stated it correctly

we will be working some more on improving the save times. nothing we can do about the larger files.
You may find that the amount of channels that the FPP support without lag would drop
Today I have 32K chanenls @ 20fps
in the future 32K channels at 100fps?

could also be written
we will be working some more on improving the save times. nothing we can do about the larger files.
You may find that the amount of channels that the FPP support without lag would drop
Today I have 32K channels @ 50ms
in the future 32K channels at 10ms

The point is 100fps or 10ms frame timing will put 5 times more load on both xlights and the fpp.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago
pmscientist wrote:The units you presented are ms, though what you're saying would make more sense if using fps. You said you were worried about going to 25ms from 10ms because of all the boxes to fill. That didn't make sense to me, 25ms timing requires fewer time slots/boxes than 10ms. Conversely, 25fps would require fewer boxes than 10fps.

awww ..... I'm going from 50ms to 25ms, not 10ms to 25ms. Solved. I was only mentioning to Sean that lots of other people use 10ms, not me. And that if they were adding timings some people might need it. Sorry for muddying up this thread.


Reply
smeighan
Posts: 2595
Topic starter
(@smeighan)
Famed Member
Joined: 15 years ago

The architecture will support any frame rate, we just dont recommend going below 25ms (40fps). If you have smaller channel count you could get away with it. This year I will probably be 48K channels.


Reply
Posts: 1763
(@santacarl)
Noble Member
Joined: 19 years ago

I just downloaded 4.00.00 off the NC website..... Is that the same version that is 50% complete?

If I install 4.0.....can I back up to the 3.06.15 version? I'm already doing some sequencing for next year so I need the save feature..... That being said I'd also like to take a peep at 4.0.......


Reply
jnealand
Posts: 956
(@jnealand)
Prominent Member
Joined: 19 years ago

If you look again, I think Sean removed the 4.0 version. It was not for anyone to try out and it is not anywhere near completion. Posted by accident he said on another forum.


Reply
smeighan
Posts: 2595
Topic starter
(@smeighan)
Famed Member
Joined: 15 years ago

yep, i was testing the 4.0.0 build process. sorry. you guys must think we leap tall buildings if we were done already.

more features went in today, it is getting filled out nicely.

We still are missing some major pieces
drag and drop effects
preview
save

a few more weeks i thinkl


Reply
Posts: 1763
(@santacarl)
Noble Member
Joined: 19 years ago
smeighan wrote:you guys must think we leap tall buildings if we were done already.
l

You mean you don't? :question:

I just figured you'd posted it so people could tinker and see what it looks like......That's why I was asking and being so cautious about installing it...... Whew....dodged THAT self inflicted wound! :biggrin2:


Reply
Posts: 26
(@razataz327)
Eminent Member
Joined: 17 years ago

Hi all my name is Garnet from Alberta Canada. This will be my second year and I am planning my display for this year and will be using pixel leds, using San Devices, and want to use Arduino boards to relays to control dumb leds both 12volt and 120volt.
Will the new xlights be able to run this set up for me or do I need to use other software?
I used some of nutcracker last year and liked it very much and would like to use xlights if possible.
Any suggestions and help greatly appreciated.
Garnet


Reply
smeighan
Posts: 2595
Topic starter
(@smeighan)
Famed Member
Joined: 15 years ago

xlights supports
E1.31
usb LOR protocol
usb LOR dmx
usb Pixelnet
usb Open DMX
usb DMx
usb D-lights
usb Renard

if you hardware runs from any of these, you are covered
san devices will drive from the e1.31 interface. i dont know how your arduinos are controlled


Reply
Posts: 26
(@razataz327)
Eminent Member
Joined: 17 years ago

HI I have not used the arduino yet but from what I have been reading they hook up to Vixen by using the generic serial in the Vixen set up. Then hooked up to the pc by a serial cord.
Thanks
Garnet


Reply
Page 3 / 4
Share: