I have finally started trying to output from the program to the pixels, and have run into a snag (what a surprise )
The sequence works on the screen, but I cannot get the pixels to respond. I have only setup one universe to test with at this time. (See attached screenshots) When I run the sequence, it looks good on the preview screen, but nothing appears to be going to the E682 and hence, the pixels. I have set everything up on the SanDevices E682, and the test codes work exactly as expected, so I do have a good signal to the pixels. Also, it does not show to have received any packets, so I suspect I have something in Xlights setup wrong.
Suggestions??
Thanks,
David Steward
dsteward wrote:I have finally started trying to output from the program to the pixels, and have run into a snag (what a surprise )The sequence works on the screen, but I cannot get the pixels to respond. I have only setup one universe to test with at this time. (See attached screenshots) When I run the sequence, it looks good on the preview screen, but nothing appears to be going to the E682 and hence, the pixels. I have set everything up on the SanDevices E682, and the test codes work exactly as expected, so I do have a good signal to the pixels. Also, it does not show to have received any packets, so I suspect I have something in Xlights setup wrong.
Suggestions??
Thanks,
David Steward
I'm no expert, but on the sequencing page in X-lights did you click on output to lights?
Yes, I did check that. The "Output to Lights" is lit up. Thanks for the suggestion.
How are you physically connecting to the e682?
Can you ping the controller?
Sent from my SM-G900V using Tapatalk
I'm not seeing universe 2 set up in xlights. Just the first 510 channels on universe 1... Still need the 90 channels for universe 2. . , on the E682, it looks like you have 2 stands of 100 pixels on outputs 1-1 and 1-2... And you element is using 183 of those pixels...
Looks like you have the unicast set properly.
Try adding universe 2 In xlights to see what happens
Just an update - I switched back to Multicast in xLights and it started working. I would have thought that Unicast would have been a better choice, as you specify a unique IP address to the software. i really do not understand the differences, but how does the software find the E682 if you do not have to specify the IP. Also, what happens when you have 2 different controller boards, each with a different IP of course. How does the software differentiate between them, by the universes that are configured?
Thanks to everyone for the suggestions. Hopefully, I'll eventually learn this stuff.
David
http://www.doityourselfchristmas.com/wiki/index.php?title=E1.31_(Streaming-ACN)_Protocol#Disclaimers this kinda explains multicast and unicast. unicast is the better way since it is sending too the controller itself not just sending the info out too anything with the e682 in multicast mode it doesnt do as many channels as it would in unicast mode you must have had something not setup right somewhere in your setups you may of had same problem I had at first my internet uses 192.168.0.??? and the e682 was setup as 192.168.1.??? I had too setup the e682 too match my ip address by forcing the 0 you might wanna check and see what your computers ip is
TazChaLet wrote: http://www.doityourselfchristmas.com/wiki/index.php?title=E1.31_(Streaming-ACN)_Protocol#Disclaimers this kinda explains multicast and unicast. unicast is the better way since it is sending too the controller itself not just sending the info out too anything with the e682 in multicast mode it doesnt do as many channels as it would in unicast mode you must have had something not setup right somewhere in your setups you may of had same problem I had at first my internet uses 192.168.0.??? and the e682 was setup as 192.168.1.??? I had too setup the e682 too match my ip address by forcing the 0 you might wanna check and see what your computers ip is
Yeah, I may have to play around with Firewall setting or Router configurations. I know I have the IP correct, and, the E682 and the computer are on the same subnet of 192.168.1.XX. I have no problem communicating with the controller using it's web interface and Chrome, but it does not seem to want to work out of xLights. Funny thing, though, it DOES work using Vixen, using the same IP, 192.168.1.206, as I am trying in xLights. In the end, I do want do to run it using Unicast as i think I am going to need the additional channels.
I do not have my second E682 yet. I have thought about trying the AlphaPix 16. Think it would be a better fit????
David
Take a look at the falcon controllers to... Lots of channels and pixels... I think it's getting lots of good reviews...

