Null Pixels
 
Notifications
Clear all

Null Pixels

13 Posts
5 Users
0 Reactions
7,624 Views
Posts: 88
Topic starter
(@dsteward)
Estimable Member
Joined: 12 years ago
[#41764]

It's me again.

I have attached a couple of screenshots showing a Pixel Spinner that I made. I had it designed using 61 pixels, but when I went to assemble it after cutting out the form on a laser, I learned that the distance from the holes on the outside of the "legs" to the next Leg was too long for the pixel spacing, so i had to skip one of the pixels and use the next one. That means that for example, pixel #7 as designed in not used, but #8 occupies the hole for #7, and so on. When it is all said and done, I ended up with 6 unused pixels and the total number went from 61 to 67.

How do I tell xLights that pixels #7, #18, #29, #40, #51, and #60 are not used and should be skipped?

Thanks,

David

Model   As Designed
Model   As Assembled

12 Replies
mikeh65
Posts: 794
(@mikeh65)
Prominent Member
Joined: 19 years ago

Why not just cut the wire and splice in extensions. Why waste the pixels?


Reply
Posts: 1049
(@phrog30)
Noble Member
Joined: 12 years ago

I'm using the exact setup. I spliced in wire as was already mentioned, but I think what you drew should work. Try and see.

James

Sent from my Nexus 7 using Tapatalk


Reply
Posts: 1015
(@gilrock)
Noble Member
Joined: 14 years ago
dsteward wrote:It's me again.
How do I tell xLights that pixels #7, #18, #29, #40, #51, and #60 are not used and should be skipped?

The answer is: "you already did". Isn't that awesome?


Reply
Posts: 88
Topic starter
(@dsteward)
Estimable Member
Joined: 12 years ago

Gil,

So if I want to skip 1, 2, 3 or more pixels, all I have to do is skip the numbers in the grid?

I am really enjoying learning xLights. Thanks for all of y'all's work

David


Reply
Posts: 1015
(@gilrock)
Noble Member
Joined: 14 years ago

I really hope that's a statement because it would disappoint me if that's a question.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

The easiest way to build this is to install every other pixel going out the leg, then every other coming back to center. Then all your moves from leg to leg would be in the center. I've used this with mini's and it works great. I'm not sure how the programming would work. But it makes the build easy and limits splices for problems.


Reply
Posts: 1049
(@phrog30)
Noble Member
Joined: 12 years ago
Skunberg wrote:The easiest way to build this is to install every other pixel going out the leg, then every other coming back to center. Then all your moves from leg to leg would be in the center. I've used this with mini's and it works great. I'm not sure how the programming would work. But it makes the build easy and limits splices for problems.

That wouldn't work if you had 3" pixels. The easiest way is what the op is doing. He's wasting pixels but I'm guessing he doesn't care.

By the way, I would blank out the null pixels with tape or paint, just in case they come on. If they come on, they will stay on.

James

Sent from my SM-G900V using Tapatalk


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

You can null pixels in some hardware. That would save the possibility of them coming on accidentally rather than paint.


Reply
Posts: 1015
(@gilrock)
Noble Member
Joined: 14 years ago

The data packets are going to already have 0's for those pixels so it doesn't matter.


Reply
Page 1 / 2
Share: