Hi,
am trying to setup for whole house model and use back into HLS.
1. when setting up XL4 , output = universe on the model setup page?
2. Is there a limit on universe capability, My P10 panels start at universe 128 (Rons Holiday Light Controller (ie 128 -191 using 128 pix per universe))
3. When I go into modify model to setup output and start channel (ie ch. 1 output 128 ) (Setup E131 has 128 x 384 ch) this is custom model;
the start and and end channel list come up as " invalid", only if I start as output 1 - does it compute channel list correctly
4. I also have a similar error in my mega tree 12 str x 25 pixels; 2 outputs univ 7 & 8, setup is correct (un7 ch 450, uni8 ch 450)
Problem is chn listing computes first output /uni as 7 x ch450 , then it goes Opt 8 x 301ch . then universe 9 kicks in and upto ch122 as last channel.
can someone help please
Have tried restart etc but same errors appear
have cleared out mode land started again - same result
Cheers Boof63
You can make the output equal the universe but that's not always the case. Some people define output 1 to be a COM port and then output 2 becomes Universe 1. Or I could define output 1 to be universe 37. It's up to you whether you defined your setup where the universe number equals the output number. It's hard to decipher your descriptions to know what's wrong. Screenshots of the setup tab and model setup would be easier. If it says invalid on the model do you have enough channels allocated in setup to cover how many you are defining in the model?
ok thanks Gil will post up some screen shots that should help.
cheers and thanks Boof63
I saw the "Invalid" pop up on me when I started trying to use the From Output fields also. All I had to do was click in one of the fields and it fixes itself. Try clicking in the start channel field. The other thing is just a display issue the actual model and output will work fine. We use absolute channel numbering underneath so everything is calculated as a fixed offset from where it starts. I would ignore it and just try to sequence things and see if you see any real errors.
Tried it Gil and no change, still comes up with "invalid" in both start and finish for the channel ccounts.
even placing output=1 just gives a start of 1 and finish of 24576
So will connect up and see later . If any ideas would appreciate .
thanks
cheers boof63
Boof63 wrote:Tried it Gil and no change, still comes up with "invalid" in both start and finish for the channel ccounts.
even placing output=1 just gives a start of 1 and finish of 24576
So will connect up and see later . If any ideas would appreciate .
thanks
cheers boof63
I can't see enough in your screenshots to tell if the "Invalid" is correct or not. Placing the output = 1 is supposed to give you start=1 finish=24576 because that's what 128*64*3 equals. Are you sure you have 24,576 channels available starting at the channel number assigned to universe 128? We have a ton of users that could tell you what's wrong if you post the xlights_rgbeffects.xml file.
Hi Gill, it appears the computer was the problem , have a new machine and all is good
Thanks for your help and apologies for wasting your time
Cheers Boof63
I did run into something today that was giving me the "Invalid" that I thought was a bug but realized I as just thinking about it wrong. The From Output field is for the output number on the Setup tab....think of it as the row number. So it doesn't always match up with the universe number. I had allocated universes 1-45 and then universe 300 and tried to put 300 in the From Output field but that is incorrect. I needed to put the output number of universe 300 which was 46 in my setup. Which bring up another deficiency in the program in my opinion. We don't actually display the output numbers so if you skip around universe numbers it would be a pain to manually count them.
I had the same brain fart moment today.....
I was trying to lay things out and use output number to reflect my Universe numbers but could not get my P10 matrix to display properly (I use one of Ron's controllers as well), I was getting invalid as well. What I did was to mimic exactly the universe and channel layout that I have in HLS in the setup tab of Xlights.
I then re-created my models in the order they are used starting from universe 1 all the way up using output 1 and adding each model using sequential channels.
I can now import HLS into Xlights and add effects and they appear as they should on specific models.
Here is a quick look at my xlights setup:





