The not so Mega Tre...
 
Notifications
Clear all

The not so Mega Tree

22 Posts
12 Users
0 Reactions
12.2 K Views
Posts: 353
Topic starter
(@bigredsoftware)
Reputable Member
Joined: 15 years ago
[#19757]

I joined DIYC just after Christmas in 2011, and I have been blown away by everyone and everything. This is my attempt to make a "Mega" tree, except it will only have 400 pixels. That would be 16 strips of 25 pixels each. This 1st post is to show how I made these. I used a Haas GR-510 CNC, and they are made of .5" thick polycarbonate. I have included pictures.
A few notes:
The holes for the pixels are .6875
I put a slight chamfer on the back of each hole; this made inserting the pixels MUCH easier.
I placed the pixels in one-by-one making sure the wires were uniform and not under any stress, e.g. no twists or bends.
This took me about 5 hrs to machine all the strips, my hands eventually gave up putting the pixels in. More to follow!
----------------------------------------------------------------------------------------------------------------------------------------------------

Ok, I updated the attachments to include the bottom, topper and 2" pvc stem. Also note the whole thing "floats" on the pvc, so the strands are always being held tight by gravity. I haven't figured out how to mount it in the yard yet or controller location ect ect.. The pvc is 96" long. I also had to widen my original .25" hole to .375 to work with these hooks. My plan for the topper went to heck; the holes are way too close. I just bent the hooks out for more space, and everything seems alright now. I may have to break/extend the middle wires between the strands.

So how'd I do folks?


21 Replies
Posts: 221
(@stenersonj)
Estimable Member
Joined: 17 years ago

Very nice. i have a similar plan. i will be using a waterjet to cut struts of steel about.050 thick. the waterjet will also cut the holes for the lights. then i will put a bend on each side of the strut to strenthen it.


Reply
Posts: 353
Topic starter
(@bigredsoftware)
Reputable Member
Joined: 15 years ago

Update above.


Reply
jaywalk101
Posts: 761
(@jaywalk101)
Prominent Member
Joined: 15 years ago

Very cool design! I wish I could so something like this!!! This will make your effects look very good having all the pixels evenly spaced out.... Thanks for sharing!


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago

Your so called "not-so-mega" mega-tree beats the heck out of my "not-mega-at-all" tree!! I only wish I had pixels on my tree now - you have 400!! Wow. Nicely done.


Reply
boyelroy11
Posts: 757
(@boyelroy11)
Prominent Member
Joined: 17 years ago

That's pretty sweet. Nice to have toys at your disposal 🙂 Curious as to whether the polycarbonate will pick up and disperse light, or maybe do the edge lighting thing.


Reply
Posts: 353
Topic starter
(@bigredsoftware)
Reputable Member
Joined: 15 years ago

I discovered a cool PVC flange @ Menards, grabbed a scrap of 1.25" at work, now we have a base. I figure everything else will be wire to hold it down (not that it COULD blow away) when out in the grass. Now I have some wiring to figure out, and an enclosure to build.

IMG 1620 (450x800)
IMG 1621 (450x800)

Reply
boyelroy11
Posts: 757
(@boyelroy11)
Prominent Member
Joined: 17 years ago

A little black spray paint on the center pole, and you will be all set- looks great!


Reply
Posts: 564
(@jackfrost)
Honorable Member
Joined: 16 years ago

WOW ! ! ! that is SUPER . Any chance of getting a short vid of you lighting it up ( in the dark preferable ) so we can see if it "glows" around each of the LEDs on the plastic strip .


Reply
james70818
Posts: 2045
(@james70818)
Noble Member
Joined: 19 years ago

Well, you might as well order some clear pvc pipe for the center support.

Looks great,
James


Reply
Page 1 / 3
Share: