sectional mega-ish ...
 
Notifications
Clear all

sectional mega-ish tree

14 Posts
8 Users
0 Reactions
7,739 Views
Posts: 46
Topic starter
(@davejackson)
Trusted Member
Joined: 18 years ago
[#15007]

Hey all,

I am getting ready to start building my mega tree and I am hoping for ideas and or experienced assistance. I want to build a horizontal sectional mega tree. It can only be about 10-12ft tall. I do have some ideas on how to build it but I wanted to fish around for someone who has either built one or has a similar idea.

I was planning on making it 4 horizontal sections using a steel pole center and slipping pvc over the center pole in 3ft sections connected by a pvc coupler. On that coupler I was thinking of securing smaller pvc endcaps that would radiate out to form spokes. On the end of the spokes I was thinking of using the same technique that most use to form traditional mega bases, pvc and T's. I need to vertically support those sections either with wire and eye hooks or vertical sections of pvc.

This thing might be a flimsy mess when I am done, but I'll McGuiver it up somehow. I will just need to stock up on chewing gum and 9 volt batteries.

Has anyone ever made anything like this?

Thanks,
Dave


13 Replies
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

I'm having trouble envisioning your design, mostly because my pea-brain is in conflict over the vertical nature of most mega-trees yet you want horizontal sections. Are you talking about making it in pieces to stack on top of one another? It'd sure help if you could put together a bit of a sketch....


Reply
Posts: 347
(@standinginawe85)
Reputable Member
Joined: 17 years ago

I think I understand what you're trying to do - probably because I've thought about doing something similar in the past. In my mind, the PVC spokes don't seem necessary. If you have enough vertical supports (aka thin wire going from the top of the pole to the ring around the base and/or stakes in the ground), and you put that same wire where you were going to put the spokes, it should work. As a side note, this is because I don't like my audience to see a lot of the support structure of a display, I feel it takes away from the overall "wow" factor. You'll still need the PVC rings around the outside though, and be able to ensure the center pole is exactly vertical and well anchored (guy wires). One more thing, don't get that cheap and flimsy PVC for the rings... it's nice when you're thinking about how easy it is to bend, but in the end you'll end up with a squarish circle instead of a nice perfectly round one.


Reply
bcstuff
Posts: 449
(@bcstuff)
Reputable Member
Joined: 16 years ago

I have seen people do like 1 or 2 horizontal section to help keep the strings from sagging in the center on a really tall tree, but I don't think they sag that much, especially at only 10-12 feet tall. You would be better off just making your base and a pole and running your strings down, shouldn't be much sagging in that short of a distance.


Reply
Posts: 11
(@rescue-653)
Active Member
Joined: 16 years ago

This is the tree that I did this year I will get you some more pictures of the night shot. I built it completly out of 1 1/2" PVC I built the rings first and installed T's that create the joints to connect each ring. There are a total of 5 sections in height and there are 8 sections in each row of height, I run three colors per section also. Basiclly it was a channel hog at a total of 120 channels but looked amazing and got alot of compliments.

Mega 1
mega2

Reply
IdunBenhad
Posts: 1603
(@idunbenhad)
Noble Member
Joined: 18 years ago

Hi:
My megatree was a 10' section of conduit with floor flanges on each end. The bottom floor flange had three long spikes driven into the ground and the top floor flange was drilled with 32 holes used to attach the 32 strings of 100 minilights attached at the centers of the strings.

The bottom was PVC in a circle. I used 16 sections around the base with 22.5 degree elbows. 8 of the sections were wrapped with 100 bulb strings making a total of 40 channels for the tree and base. 8 of the sections were split and a "T" inserted pointing down and a 7" length of PVC used as a leg. The leg was drilled in one side near the bottom and a spike driven into the ground. It was about 7" off the ground.

It withstood some high winds with no problems as the light strings also served as guy lines.

The base system was too large, but will be cut down this year to a smaller diameter and all the base sections wrapped with lights. Also, this year the tree will probably be on top our new house. We didn't have a house this last season.

One advantage to living in Yuma, AZ is no snow and rain is a rarity.


Reply
Posts: 46
Topic starter
(@davejackson)
Trusted Member
Joined: 18 years ago
rescue_653 wrote:This is the tree that I did this year I will get you some more pictures of the night shot. I built it completly out of 1 1/2" PVC I built the rings first and installed T's that create the joints to connect each ring. There are a total of 5 sections in height and there are 8 sections in each row of height, I run three colors per section also. Basiclly it was a channel hog at a total of 120 channels but looked amazing and got alot of compliments.

Yeeeahh Rescue! Bam!! Like that! Does your tree have a center pole or is it "free standing"? Was it pretty sturdy? I am sure you guyed it down, but was it attached to the ground? I was going to use a center pole so I could use the inside as a lighted sectional fire pole. When animated it could shoot up and set off the star. I was also going to attach the horizontal pvc sections to the center pole with spokes. I like the way you used the 22.5 angles. That seems better than my idea of bending sections. It will also allow me to use cross connectors to secure each section.

Ok next question for you. Did you figure out a way to break it down and store it without taking the lights off?

I was only going to use the horizontal sections as channels, so with 4 sections each with red, green and white that would only be 16 channels plus the star. If I laid out the lights right it would be relatively easy to add channels that wrap around each section like you did.

I tried to attach a screen shot of what I want the finished project to like like animated and a very rough sketch.

Thanks for the help and advice.
Dave

Screen shot vixen

Reply
Posts: 11
(@rescue-653)
Active Member
Joined: 16 years ago
davejackson wrote:Yeeeahh Rescue! Bam!! Like that! Does your tree have a center pole or is it "free standing"? Was it pretty sturdy? I am sure you guyed it down, but was it attached to the ground? I was going to use a center pole so I could use the inside as a lighted sectional fire pole. When animated it could shoot up and set off the star. I was also going to attach the horizontal pvc sections to the center pole with spokes. I like the way you used the 22.5 angles. That seems better than my idea of bending sections. It will also allow me to use cross connectors to secure each section.

Ok next question for you. Did you figure out a way to break it down and store it without taking the lights off?

I was only going to use the horizontal sections as channels, so with 4 sections each with red, green and white that would only be 16 channels plus the star. If I laid out the lights right it would be relatively easy to add channels that wrap around each section like you did.

I tried to attach a screen shot of what I want the finished project to like like animated and a very rough sketch.

Thanks for the help and advice.
Dave

Yes I did use a center pole which is also what my star is attached to. But I stood the center pole up with 4 guy wires and then I run a couple sets of wires from the PVC base to the center pole to help keep the tree from wanting to shimmy in wind. Also I run 4 guy wires from the top of my pole to the ground and tied this set off to the PVC to help support it. But as for the stability of the tree it was good and actualy the first night it was up we had a severe thunderstorm come through and actual knocked out power and a large oak tree at the neighbors and it stood fine and also faired well during the Christmas snowstorm.


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

Yeah, and rescue has that neat lift/bucket arm that makes it super easy to put this up! Of course, I'm jealous...


Reply
Posts: 11
(@rescue-653)
Active Member
Joined: 16 years ago
mschell wrote:Yeah, and rescue has that neat lift/bucket arm that makes it super easy to put this up! Of course, I'm jealous...

Now Mark you dont have to be jealous its not like I dont live 15 minutes down the road from you


Reply
Page 1 / 2
Share: