Noob: First time me...
 
Notifications
Clear all

Noob: First time mega tree

28 Posts
14 Users
0 Reactions
10.1 K Views
Posts: 74
(@drewfus)
Estimable Member
Joined: 12 years ago

Just a thought to save money a 4 port controller would work great for just the tree. I just use a E6804 form sandevices to drive 16 strands of 93 pixels each that are 5v from ray wu.


Reply
Posts: 944
(@didjareally)
Noble Member
Joined: 12 years ago

Might as well get a f16v2 cause you won't want to stop at a mega tree, then you'll be ready for the additional pixels and props


Reply
Wolfie
Posts: 2225
(@wolfie)
Noble Member
Joined: 11 years ago

Yea, +1 on the F16V2. Seriously. Its worth the money in capability and scaleability of your display.

Don't forget to think about the topper, if you intend to put one up.

Last year I put up a 24 strand 180 deg tree. I used 5v bullet pixels and I ran it off a Joshua1 Systems P12 (J1Sys P12 as its commonly refered to). It was supported by 3/4" black iron pipe with 4 guys. The topper was a coro star with 35 3x5050 modules (12v). It was built with the pixels being supported by box strapping.

It worked. But. I underestimated the height needed as a mis-measured the length of the legs so it ended up squat and fat with the pole being too short.

This year I am scrapping it and rebuilding using 12v square pixels and will be driving it with a Falcon F16V2 board. I will be doing it right and using boscyo strips. The center pole will be a JUMP mounted on portable hole (monkhouse). This will make it completely free standing with no guy wires. The same star will go on top as before as it was fine. The whole tree will now be 12v.

The tree will start life as a giant pumpkin. The pole will be collapsed down to minimum height and a topper of a stem will be on top. Hoops will clamp to the pole and the pixel strips will drape around the outside and be gathered together at the bottom to form a ball. It will go up for Halloween. Conversion to a tree will be as simple as swapping the topper, removing the hoops, and raising the pole to full height and securing the bottom of the pixel strips to form a cone. Same controller, same wires, same everything. Only thing that changes is the topper.

Here is what you need to know:
http://www.boscoyostudio.com/products/index.php?main_page=product_info&products_id=2
http://www.magicchristmas.org/uploads/3/4/0/0/3400701/monkhouse_jump_2010_version0001_copy_2.pdf
http://www.magicchristmas.org/uploads/3/4/0/0/3400701/portable_hole_ii_copy_2.pdf
http://www.joshua1systems.com/products/lighting/ECG-P12.html (Older controller and site is very out of date, still a cheap good controller)
http://pixelcontroller.com/store/index.php?id_product=38&controller=product (Get this. You won't be sorry)
http://www.aliexpress.com/store/701799 (Ray Wu)


Reply
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

if you have a large yard having all the channels in one place isn't always the best way too go some smaller controllers around the yard will make for less cords and the need for null pixels

didjareally wrote:Might as well get a f16v2 cause you won't want to stop at a mega tree, then you'll be ready for the additional pixels and props

Reply
Wolfie
Posts: 2225
(@wolfie)
Noble Member
Joined: 11 years ago

True that. However starting out new with a central location offers a less complicated start. Adding additional controllers later is always an option as is moving that larger controller to a new location to suit the display.

Also, with the forthcoming differential expansion board for the F16, distance runs are not going to be a problem. And with some basic soldering you can whip up Max485 chips into boards and send 4 lines down a single Cat5 cable.

Problem (and advantage) is there are as many ways to skin a cat as there are people putting out displays. Rarely is there only one way to do something.


Reply
Posts: 944
(@didjareally)
Noble Member
Joined: 12 years ago
TazChaLet wrote:if you have a large yard having all the channels in one place isn't always the best way too go some smaller controllers around the yard will make for less cords and the need for null pixels

That's why there are differential and receiver boards, plentyof room to expand later. 🙂


Reply
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

sorry but find your statement wrong you dont buy a board for pixel and have too buy more too run somewhere else off that board I have a alpha 4 setup in 1 area it works all the stuff around it I need worked I also have a 682 for my mega and a px1 for a prop on my roof and then all my renard boards each one doesnt have too run other boards around my yard I dont see why you want a board that does so many pixel located in 1 spot if you arent gonna use the function of that board buy the board you need for that area just my opinion and it isnt worth anything since we all have them

didjareally wrote:That's why there are differential and receiver boards, plentyof room to expand later. 🙂

Reply
Posts: 383
(@aesl1982)
Reputable Member
Joined: 12 years ago
TazChaLet wrote:sorry but find your statement wrong you dont buy a board for pixel and have too buy more too run somewhere else off that board I have a alpha 4 setup in 1 area it works all the stuff around it I need worked I also have a 682 for my mega and a px1 for a prop on my roof and then all my renard boards each one doesnt have too run other boards around my yard I dont see why you want a board that does so many pixel located in 1 spot if you arent gonna use the function of that board buy the board you need for that area just my opinion and it isnt worth anything since we all have them

For the price of your 682 and ur alphapix 4 u could have a f16v2-r with 16 ports that can go up to about 20-30 ft. Then have the differential board and expansion which will give u another 16 outs puts up to many hundreds of frets away from controller. All operates from one central location. Less cable less wire less headache less controllers less everything. Pretty cool system actually


Reply
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

for 1 you dont know how much I paid for what I have I did not buy them new I worked for them helping others doing sequencing for them and building for them in my area I understand about the f16 board but in my opinion I like having my boards where I need them if your 1 board goes out you are down whole show if 1 of my boards go out part of my show is still running and I leave room on my boards for a safety net just in case, I can run wire with nulls if need be too other board in hurry too get show back up but we all have own opinions on things I know someone who has several f16 boards he replaced his 682s at end of last yr doesn't even come close too using his ch on 1 board in the area he has it and on other side of his yard is another board with a lot of room on it his front yard is large (wide)

aesl1982 wrote:For the price of your 682 and ur alphapix 4 u could have a f16v2-r with 16 ports that can go up to about 20-30 ft. Then have the differential board and expansion which will give u another 16 outs puts up to many hundreds of frets away from controller. All operates from one central location. Less cable less wire less headache less controllers less everything. Pretty cool system actually

Reply
Posts: 1168
(@keith-r)
Noble Member
Joined: 19 years ago
BZ-MikeH wrote:Hello Everyone,
I'm new to this "hobby" and am looking to get my feet wet with doing a Mega tree for the first time this year. I see premade kits for these are available but I would prefer to do my own thing being budget friendly 🙂 What are the most popular controllers to use for a 12 strand tree? Are they are any good tutorials for beginners? Thanks guys!

Getting your feet wet, aye? On a budget, aye? I am not going to get into this is better or that is better, BUT, if you are looking to save some dough, and have some experience soldering, then I would pick the E682 for your budgetary needs. If you don't have soldering experience, and want to buy a board that is already put together and tested, and gives a little more capability, and is expandable later on, I would choose the F16v2. I run both in my show, and with a little more than 10,000 channels and an additional 100 AC channels, both are rock solid performers. The E682 is about half the price of the F16V2, but you will have to do some soldering to put it together, unless you buy the pre-built version, then the price is about the same and the F16v2 may have an edge.
Make sure you have a good handle on what you are trying to accomplish, a general layout of your show, and select the type of pixels (and voltage) that you want. You will need to get started building those models now and order the equipment and lights you will need to fill your show. It is late in the season to get started, but it is doable. I would read the forums for ideas on your mega tree, and check out Sandevices website and read the manual for the E682 and do the same on the FalconChristmas site and see which on the controllers you like and which you think you will be able to set up easiest. It might boil down to whether or not you are comfortable soldering. Good luck.
Another thing is that there are a lot of people that can help if they are close by. If you put your location in your profile, people will know what area you are in.


Reply
Page 2 / 3
Share: