Mega Tree Convertin...
 
Notifications
Clear all

Mega Tree Converting to Pixels>>>>HELP!!!!

7 Posts
3 Users
0 Reactions
6,398 Views
Posts: 344
 TSL
(@tsl)
Reputable Member
Joined: 10 years ago

Mine a connected with short Ray Wu 3 wire waterproof connectors at the top. About 4’ of wire and Ray Wu connectors for the controller at the bottom. Data goes up string one and down string two. I didn’t solder mine because, for me, it’s easier to put up and take down. I have 32 strings using 16 ports. Keep in mind if you do it this way you will probably need to power inject into your strings. I need to on mine since I’m a 5v pixel user. I could consolidate them down even more if I would need the additional ports. But I don’t right now so I’ll cross that bridge when I need to.

Sent from my iPhone using Tapatalk


Reply
Posts: 49
Topic starter
(@dreamer78)
Trusted Member
Joined: 16 years ago

Purely subjective. I use distance from viewer to control spacing. The closer the viewer, the closer the spacing. Up to 5m I use 1" spacing. 5m-10m I use 2" spacing. Beyond 10m I use 3" spacing. This is NOT a hard and fast rule. It is what looks good to me. You need to decide what is best for your show.

"Based on this, I can go with 3" spacing."

My Pixel tree is 16 strings and 360 degrees and looks good. Having put it together, I cannot imagine doubling the density. Just the lift weight would become a PITA.

"I plan to do a 180 degree tree with patterns and video clips. Using the mega tree calculator on another thread, I come up with about 4 1/8" between strings at the bottom and less than 1" at the top(based on 32 strings). Would this give good definition for video clips?"

I use the Falcon series controllers. Rock solid and very flexible. Many others use the SanDevices controllers and seem to have good success (I dont have any).

"I plan to use the Falcon V3 controller and two 350 watt Meanwell power supplies and 16 output ports. Would this work for what I am planning?"

You seem to be using the term strip but you are implying string. Usually we use the term Strip to refer to a flexible PCB with Tri-color LEDs soldered to it and ws281x driver chips to drive the LEDs. The WS2811 version generally comes in a 3:1 configuration (three sets of LEDs per driver chip) [these can be cut every three LEDs] and the ws2812 (and higher) versions have a tri-color LED bonded to the ws2811 driver chip [cut between any two pixels].

Strings are a pixel driver chip and a tri color LED molded into a bullet or square shape with wires running between them. These can be cut at any point.

"I plan to use the 2811 STRINGS(learning terminology), so are you saying they can be cut anywhere between pixels(bulbs)?"

I think you are talking about an output port on the pixel controller. In general the number of pixels you can attach to a single string on an output port from a pixel controller is limited by two things (I will use WS2811 timing for my examples):

  • Refresh rate:
  • Real motion is considered to be 25ms per frame. This limits the number of pixels on a string to 680 pixels or less. I limit my strings to 600 pixels.
  • The next most popular refresh rate is 50ms per frame. This limits the number of pixels on a string to 1360 pixels or less.
  • The pixels do not care about refresh rate and are designed to have an infinite length. This means a refresh rat of once per day is possible but not useful for us.

Controller capacity. Most of the pixel controllers available today have a pixels per port capacity of 200 - 1200.

"So a pixel string of 50 is 50 pixels?"

See above. I can do 6 legs of my tree on a single pixel controller port. I choose to do 4 legs per port because I like symmetry.

Most pixel controllers are E1.31 based. This means you are setting up an Ethernet network to distribute the lighting data from the show player to the pixel controllers. Ethernet cannot be daisy chained. However, some pixel controllers have a built in Ethernet hub/switch which allows the E1.31 data on the network to be forwarded through a controller (kind of like daisy chaining).

"So would need a separate ethernet cable running to my pixel controller?"

Look at Falcon and SanDevices.


Reply
Page 2 / 2
Share: