Mega Tree Convertin...
 
Notifications
Clear all

Mega Tree Converting to Pixels>>>>HELP!!!!

7 Posts
3 Users
0 Reactions
6,397 Views
Posts: 49
Topic starter
(@dreamer78)
Trusted Member
Joined: 16 years ago
[#52237]

I've had an animated display for 8 years and decided to begin converting to pixels. I want to begin with my mega tree and need lots of help as I know virtually NOTHING when it comes to pixels. I believe in doing it right the first time regardless of cost so I don't have the expense of doing it over.Questions and thought
-I'm looking to do a 180 pixel tree,string lengths will be approx. 16' based on 17' height and 8.5' diameter(2:1)
-What is the best pixel spacing to give the best definition?
-Is 16 strips enough to give good definition or do I need to go to 24/32?
-Here's the controllers i'm looking at https://www.holiday-light-express.com/light_information.php?partnumb=RGB-Command-Center&stock_printout=
-Pixels https://www.holiday-light-express.com/light_information.php?partnumb=RGB-12mm-100C-Bl&stock_printout=
-I read that pixels can be cut to length?
-1 channel per pixel strip?
-16 strips/1 controller 24/32 strips/2 controllers?
-Can the data be daisy chained along with other LOR controllers or need to be separate?
-Pixels and controllers are vendor I have bought from for years, any other suggestions?
-Articles or video suggestions?
-Many more questions to come from a pixel neophyte

Thanks for all your help. Cliff


6 Replies
Posts: 344
 TSL
(@tsl)
Reputable Member
Joined: 10 years ago
dreamer78 wrote:I've had an animated display for 8 years and decided to begin converting to pixels. I want to begin with my mega tree and need lots of help as I know virtually NOTHING when it comes to pixels. I believe in doing it right the first time regardless of cost so I don't have the expense of doing it over.Questions and thought
-I'm looking to do a 180 pixel tree,string lengths will be approx. 16' based on 17' height and 8.5' diameter(2:1)
-What is the best pixel spacing to give the best definition?
-Is 16 strips enough to give good definition or do I need to go to 24/32?
-Here's the controllers i'm looking at https://www.holiday-light-express.com/light_information.php?partnumb=RGB-Command-Center&stock_printout=
-Pixels https://www.holiday-light-express.com/light_information.php?partnumb=RGB-12mm-100C-Bl&stock_printout=
-I read that pixels can be cut to length?
-1 channel per pixel strip?
-16 strips/1 controller 24/32 strips/2 controllers?
-Can the data be daisy chained along with other LOR controllers or need to be separate?
-Pixels and controllers are vendor I have bought from for years, any other suggestions?
-Articles or video suggestions?
-Many more questions to come from a pixel neophyte

Thanks for all your help. Cliff

You’re doing exactly what I did 4 years ago. I had LOR 120v tree. Converted it to pixels. 1st 3 yrs had 16 2” spaced 91 pixel per strip tree. It looked ok. Last year I added 16 more strips for a total of 32. Made a huge difference in looks. I run the 32 strips off of an F16 v3. Yes pixels can be cut.I did 1 channel per 2 strips. Zig zag them. My controllers, Falcons, can be daisy chained but I do not daisy chain them. Yes you can run LOR controllers, I’m assuming your asking about your 120v ones. That requires a little more to do.


Reply
MartinMueller2003
Posts: 7614
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago
dreamer78 wrote:
-What is the best pixel spacing to give the best definition?

Purely subjective. I use distance from viewer to control spacing. The closer the viewer, the closer the spacing. Up to 5m I use 1" spacing. 5m-10m I use 2" spacing. Beyond 10m I use 3" spacing. This is NOT a hard and fast rule. It is what looks good to me. You need to decide what is best for your show.

dreamer78 wrote:
-Is 16 strips enough to give good definition or do I need to go to 24/32?

My Pixel tree is 16 strings and 360 degrees and looks good. Having put it together, I cannot imagine doubling the density. Just the lift weight would become a PITA.

I use the Falcon series controllers. Rock solid and very flexible. Many others use the SanDevices controllers and seem to have good success (I dont have any).

dreamer78 wrote:
-I read that pixels can be cut to length?

You seem to be using the term strip but you are implying string. Usually we use the term Strip to refer to a flexible PCB with Tri-color LEDs soldered to it and ws281x driver chips to drive the LEDs. The WS2811 version generally comes in a 3:1 configuration (three sets of LEDs per driver chip) [these can be cut every three LEDs] and the ws2812 (and higher) versions have a tri-color LED bonded to the ws2811 driver chip [cut between any two pixels].

Strings are a pixel driver chip and a tri color LED molded into a bullet or square shape with wires running between them. These can be cut at any point.

dreamer78 wrote:
-1 channel per pixel strip?

I think you are talking about an output port on the pixel controller. In general the number of pixels you can attach to a single string on an output port from a pixel controller is limited by two things (I will use WS2811 timing for my examples):

  • Refresh rate:
  • Real motion is considered to be 25ms per frame. This limits the number of pixels on a string to 680 pixels or less. I limit my strings to 600 pixels.
  • The next most popular refresh rate is 50ms per frame. This limits the number of pixels on a string to 1360 pixels or less.
  • The pixels do not care about refresh rate and are designed to have an infinite length. This means a refresh rat of once per day is possible but not useful for us.

Controller capacity. Most of the pixel controllers available today have a pixels per port capacity of 200 - 1200.

dreamer78 wrote:
-16 strips/1 controller 24/32 strips/2 controllers?

See above. I can do 6 legs of my tree on a single pixel controller port. I choose to do 4 legs per port because I like symmetry.

dreamer78 wrote:
-Can the data be daisy chained along with other LOR controllers or need to be separate?

Most pixel controllers are E1.31 based. This means you are setting up an Ethernet network to distribute the lighting data from the show player to the pixel controllers. Ethernet cannot be daisy chained. However, some pixel controllers have a built in Ethernet hub/switch which allows the E1.31 data on the network to be forwarded through a controller (kind of like daisy chaining).

dreamer78 wrote:
-Pixels and controllers are vendor I have bought from for years, any other suggestions?

Look at Falcon and SanDevices.

dreamer78 wrote:
-Articles or video suggestions?

AUSChristmas has a great primer on using pixels.


Reply
Posts: 49
Topic starter
(@dreamer78)
Trusted Member
Joined: 16 years ago

Tried to reply without quote


Reply
Posts: 49
Topic starter
(@dreamer78)
Trusted Member
Joined: 16 years ago
TSL wrote:You’re doing exactly what I did 4 years ago. I had LOR 120v tree. Converted it to pixels. 1st 3 yrs had 16 2” spaced 91 pixel per strip tree. It looked ok. Last year I added 16 more strips for a total of 32. Made a huge difference in looks. I run the 32 strips off of an F16 v3. Yes pixels can be cut.I did 1 channel per 2 strips. Zig zag them. My controllers, Falcons, can be daisy chained but I do not daisy chain them. Yes you can run LOR controllers, I’m assuming your asking about your 120v ones. That requires a little more to do.

By zig zag, do you mean 2 strings soldiered together at the top with data pigtail at bottom of string 1?


Reply
Page 1 / 2
Share: