pmiller wrote:How do I go about getting some of these? I don't own a 3D printer![]()
Sent from my SM-T710 using Tapatalk
Try 3D hub
Sent from my iPhone using Tapatalk
Dirwich wrote:How did you get your 24/48 strand topper? (i.e. did James make this custom for you?) The largest available on his website is the 16/32... Also, do you know approximately what the outer diameter of your topper is?For that matter, does anyone know what the outer diameter of the 16/32 topper from Boscoyo is?
8 3/4" is the 16/32 topper outer diameter.
Sent from my iPhone using Tapatalk
Dirwich wrote:How did you get your 24/48 strand topper? (i.e. did James make this custom for you?) The largest available on his website is the 16/32... Also, do you know approximately what the outer diameter of your topper is?For that matter, does anyone know what the outer diameter of the 16/32 topper from Boscoyo is?
8 11/16
Sent from my SM-T710 using Tapatalk
Hi Wolfie, I just noticed the connectors on your strands... I have been trying to find a good outdoor connector to standardize on. What series did you end up using on your strands, and would you use them again?
Dirwich wrote:How did you get your 24/48 strand topper? (i.e. did James make this custom for you?) The largest available on his website is the 16/32... Also, do you know approximately what the outer diameter of your topper is?For that matter, does anyone know what the outer diameter of the 16/32 topper from Boscoyo is?
I guarantee James knows precisely how big they are.
I will measure mine and let you know.
Yes, James made it custom. I am sure he will make you one too. Just call or email him. I wanted one with no large center hole but with a small hole as a center reference to take the two floor flanges and for 24/48 configuration.
pmiller wrote:How do I go about getting some of these? I don't own a 3D printer![]()
Sent from my SM-T710 using Tapatalk
There are many 3D print houses, as mentioned 3D hub is one. You can take the design file I posted and have it printed anywhere for your own use. You just can't take it and have it printed to sell.
Dirwich wrote:Hi Wolfie, I just noticed the connectors on your strands... I have been trying to find a good outdoor connector to standardize on. What series did you end up using on your strands, and would you use them again?
They are Delphi Weather-Pack that I purchased from Waytek Wire (most likely the cheapest source). Use them again? Yes. I going to remove all my pigtails everywhere and convert over to these this coming summer/fall. I have a mixture of Ray Wu 3p and 4p pigtails as well as 3p pigtails from Todd. I hate it because there is no "standard". Nobody's pigtails fit any others. Its stupid. I am done with that aspect of this DIY.
The only "maybe" here is I may continue using Todd's 3p pigtails coming out of the CG1500's off the controller. This may be the only place I leave pigtails. There is no soldering here. There is no heat shrink here. And I usually don't run much power off the controller so no issue with 18ga wire. In this situation its much easier to slip a pigtail through the gland, screw on a greenie and be done. Zero putz factor. The other half, obviously requires soldering to the cable and heat shrink. So thats why the maybe. I still have to make a decision here. Due to the bulk of the larger Delphi connector, a pigtail (with associated solder job) seems to make more sense. But I am unifying on a single vendor pigtail as well.
Here is where I ordered from:
https://www.waytekwire.com/products/20/Weather-Pack-Connectors/&pageSize=36
Their site is slow and marginal at best. The products are good stuff though.
I did a video review of my fist order here:
Description has links to all the products covered in the review.
I got the $22 crimpers and the $5 pin extractor. Worth the price. I purchased 3p and 2p shells and pins for 22, 16 and 12ga wire with boots. So I can make up connectors for cat5, security wire or heavy power feed wires using the same shells with different pins/boots. And that means I can also run large wire for power and small wire for data in the same connector. I haven't. But I can. Can't do that with pigtails. They are pre-wired with whatever wire they are supplied with. And you are stuck with that.
If you are looking at these, you will likely need the green boots for pixel wires. Grey boots for security wiring (though some may use green boots depending on the insulation thickness). Red (brick red) for cat5. Blue for larger 14ga and 12ga power injection. Three size ranges for pins. The smaller ones fit cat5. The middle ones fit both security wire and pixel wire both and will be your go-to size most of the time. Larger ones fit 12-10ga power feed wires. The middle sized pins can be used for cat5 if you strip it longer and fold the wire back on itself, they will bind to it just fine. Still need the smaller boot though for weather seal. I mean, you are under $5 for 100 boots so getting the various sizes isn't bank breaking. I haven't seen need for the plug seal. Yet. I did buy a pack of them. Haven't used them. I didn't order any of the green "Two Way" boots. Absolutely no clue what they are for. I ordered the Male/Female 2p and 3p shells. I assume the 1p shells are used where there is a common chassis ground, we generally don't have that so I feel those are unnecessary. There are 4p flat and square as well as 6p flat shells. Haven't seen a need for those either. It would have been neat to run the 4p (3 data and a ground) or the 6p (3 data and 3 ground) for the tree but I couldn't see the practicality of the minimum order of 10 or 20 when I would only use one or two of each sex. If I find a use for more than 3p connectors, maybe.
Lets talk price. This isn't a cheap hobby. These are not going to make it any better, unfortunately. If you buy minimum quantities (200 green boots, 100 male pins, 100 female pins, and 33 of each sex of 3p shell), the order comes to $69. That works out to about $2 a connector pair. Regular price on pigtails is about $1.50 IIRC for Diyledexpress and an insane $2.99 at HolidayCoro. Todd is running presale pigtails at $1 a pair and HC is still up at $1.79 a pair (more expensive than Todd's regular price and THATS supposed to be a sale!). So these connectors at $2 a par (minimum quantities) is more than Todd's pigtails regular, and less than HC's pigtails regular. However, once you get into the higher numbers (this was only 33 pairs) the price drops below $2. And HC doesn't offer 2p pigtails that I can see. Todd does though but they are only 18ga wire which may not be sufficient for power injection (which is why I use 2p connectors). Throw in about 25c (a SWAG for cost) for heatshrink for each pigtail pair and you can see they are right in the running.
The only big drawback I have found is that the connectors are much larger and bulkier than pigtails. So, in tight places, they could be a disadvantage. Plan things right and its not a problem. And in cold weather they are stiff, but so are the pigtails. I have had a hard time unscrewing the pigtails in cold weather (by cold I mean near or sub-zero F). These are also stiffer in cold weather but I found I can keep a stubby flatblade in my had and pop them apart far easier than having to remove gloves to pinch the screw rings of pigtails and try to yank the pigtails apart.
Another drawback I can think of is there are no purchasable T's. Thats ok, I make my own anyway. But this is an additional assembly chore some avoid by buying pre-made pigtail Ts. I don't, so no big deal for me either way.
The last drawback that has recently unfolded, is that Todd is offering his pixels with pigtails pre-attached. Well, thats half the job done for you and its molded in place. Thats nice. You still have to solder/shrink the other half but, hey, convenience of only half the work. I don't know if the price is any different without pigtails on the pixels or not. For megatree building, thats seriously nice as long as your tree has only 50px per strand. If not, you have to order custom length of pixels with pigtails attached. Then you can simply screw ends together at the top and that part is done. most of the bottoms will just screw together. You will need to buy/make power T's for the bottoms. And obviously data feed cables. But its a lot of work saved for a tree. For individual props where they are not modulus 50px, not much savings and in fact a bit of a downside as you are going to have to nip them off to build the prop in most cases.
They are not that much more then pigtails when you factor in cost of heatshrink as well which is required for pigtails but not for these. They are far faster to attach and even more so if you count the time to cut and shrink the heatshrink. They don't require soldering (but some people solder the pins anyway). Shells and boots can be recovered if need be by using the removal tool (yea, you are gonna assemble one backwards at least once). They can be ordered by the thousands all year long. My delivery time from Waytek has been consistently sub 2 day delivery time.
I douched mine with dielectric grease. Completely unnecessary but I did anyway. When you get these (at least from Waytek) you can feel they already have a thin coating on the boots and shells. Waytek confirmed this coating is silicone (same stuff in dielectric grease) so they already have a weather tight seal by design and application. The extra I put in is completely unnecessary. But I still did it the first year. You know, belt AND suspenders attitude. Just in case. Next year, I won't bother except for the stuff that actually lays on the ground under snow. Ones that hang in the air, naw, not worth the time and expense for zero gain.

