Problems with a New...
 
Notifications
Clear all

Problems with a New Prop

13 Posts
4 Users
0 Reactions
12.4 K Views
TomL8345
Posts: 1356
Topic starter
(@toml8345)
Noble Member
Joined: 15 years ago
[#52777]

Problems with a New Prop - Solved!

I added a small front porch to my house this summer and have built an "archway" consisting of 2 Boscoyo Chroma Poles of 300 pixels each and an 8x37 matrix in between. I have all 896 pixels being controlled from a single port on an ESPixelStick. When I test using the PixelStick effects everything works as expected, but when I take control from the RPi and FPP there seems to be lag when I run bars across the matrix. It changes 4 of the 8 pixels in a column, instead of the entire column at once. Also when I try to run Text across the matrix I am only seeing gibberish. The setup for the Matrix section of the archway is wired correctly in XLights and previews perfectly. I am running the Show network as Multicast.

Am I pushing the limits of the ESPixelStick too far, should I add another controller into the prop? I have tried my test sequence at both 20 & 40 fps.

Suggestions?


12 Replies
TomL8345
Posts: 1356
Topic starter
(@toml8345)
Noble Member
Joined: 15 years ago
MikeKrebs wrote:Gibberish would indicate a mapping problem. I would fix that first and then see if you are having problems. I thought sporadic has indicated that 8266 based espixelstick would ruin 680 pixels reliably at 40 fps. You are defintely over that number but if the mapping is messed up, you might just be seeing fragments from the mapping.

I don't think the mapping is the issue, rather trying to run too many pixels. I will add another pixelstick to the prop and see how that works.


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

The ESPixelStick can drive in excess of 1000 pixels without an issue.


Reply
TomL8345
Posts: 1356
Topic starter
(@toml8345)
Noble Member
Joined: 15 years ago

I shortened the string down to 586 pixels and am still having the same issues. Whenever I run a test sequence on FPP for the Matix a simple Bars pattern is jerky and even simple TEXT does not display properly. I am using XLights and the actual prop matches the wiring views in XLights. I am running a horizontal 8x37 grid starting in the upper left corner of the matrix

Porch Matrix Wiring Diagram front

so I don't think it is a mapping issue. What else would you suggest?


Reply
TomL8345
Posts: 1356
Topic starter
(@toml8345)
Noble Member
Joined: 15 years ago

bump


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Jerky sounds more like a network issue. Things not displaying right is usually a patching issue.

Are you using unicast or multicast?
Is your network quiet or noisy?
Is the player connected to the wired interface on your AP?


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago

Hi Tom, I think you can login to the ESPixelStick and check for dropped (or lost) packets, what does that say? I think if you power down it resets the value so you can do a couple of tests with the same setup.


Reply
TomL8345
Posts: 1356
Topic starter
(@toml8345)
Noble Member
Joined: 15 years ago
Barnabybear wrote:Hi Tom, I think you can login to the ESPixelStick and check for dropped (or lost) packets, what does that say? I think if you power down it resets the value so you can do a couple of tests with the same setup.

Hi Barnaby,

Here is what I have on the stick at the moment:
E1.31 Status
Universe Range 50 to 53
Total Packets 3237
Sequence Errors 378
Packet Errors 0
Source IP 192.168.73.115

I will do some more testing tomorrow.


Reply
TomL8345
Posts: 1356
Topic starter
(@toml8345)
Noble Member
Joined: 15 years ago
MartinMueller2003 wrote:Jerky sounds more like a network issue. Things not displaying right is usually a patching issue.

Are you using unicast or multicast?
Is your network quiet or noisy?
Is the player connected to the wired interface on your AP?

I am going to try to move the pixelstick in relation to my AP and see if it improves the jerkiness. I am testing in my workshop and there are some obstructions between the AP and the ESP module.

I am using Multicast
Network should be quiet. It is just a RPi with the Ubiquiti Nano Loco M2 connected right to it.
So Yes, the player is connected to the wired interface on my AP.


Reply
Posts: 116
(@coaster)
Estimable Member
Joined: 15 years ago

How much other Wifi traffic is there around you? Because the ESP runs at 2Ghz there are only 3 channels that can be used. If there is a lot of 2Ghz Wifi around you that could be contributing to the lag. You can use the Loco M2 to analyze the traffic around you and pick a less used channel. My experience is that the Loco M2 does not always pick the best channel on startup.


Reply
Page 1 / 2
Share: