Notifications
Clear all

P10 Hookups

80 Posts
11 Users
0 Reactions
29.4 K Views
Posts: 793
Topic starter
(@covewi)
Noble Member
Joined: 17 years ago

Mr Grumpy - do you have a link to the fuse block and what gauge wire does is suggested from the PS and to the panels?


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

Terminal boards: You get 3 boards for $1.18. I'm west coast (Calif) got them in 2 weeks. Freight included in the price.
https://www.aliexpress.com/item/Promotion-3-Pcs-3-Positions-3P-Dual-Rows-Covered-Barrier-Terminal-Block-Strip/32429938370.html?spm=2114.13010608.0.0.o9aHaC

Resettable Fuses: each fuse feeds 2 - P10. Got in 5-7 days these are about $0.16 each. Small freight charge $1-$3
http://www.taydaelectronics.com/poly-switch-resettable-ruef-series-30v-3a.html

The red wires came with the P10 marked as 1.5mm, or about #14, but looks more like #18 then that splits to 2 smaller wires, maybe #20 or smaller.
You should get cables and plugs with your P10 - if not the plugs are a bear go elsewhere for your panels.
I fuse this at 3A so #20 would work....but I would do #18 & # 20

The black leads from the power supply to terminal board/fuse blocks are #14 (that's what I had.) I feed 2 x 3A fuses so #18 would work here too.

Spec's say I should draw more current, but I go on reality. Measured current + 20% then test full load for 24 hours.
Don't remember the measured current per panel, pair or the lot of 12, but I can burn a 12 panel US Flag continuous without a problem.

Adding Image:

IMG 3864

Reply
jnealand
Posts: 956
(@jnealand)
Prominent Member
Joined: 19 years ago

I can run a 4 panel portable setup off a 10400mah battery pack all day. Really surprised me.


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Never seen those resetable fuses before. How do they work?

Sent from my SM-T710 using Tapatalk


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

See here: https://en.m.wikipedia.org/wiki/Resettable_fuse


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Doesn't sound like something I want to use. Once tripped the resistance goes up meaning less power. Besides, there's no way to tell one has been tripped without using a voltmeter. Article says fuse provides same protection but must be replaced when blown. Easier to tell if a fuse is blown.

Sent from my SM-T710 using Tapatalk


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago
pmiller wrote:Doesn't sound like something I want to use. Once tripped the resistance goes up meaning less power. Besides, there's no way to tell one has been tripped without using a voltmeter. Article says fuse provides same protection but must be replaced when blown. Easier to tell if a fuse is blown.

Sent from my SM-T710 using Tapatalk

I believe it shuts down current, then needs to be removed from power to reset. They do degrade a minute amounts each trip, but shouldn't degrade enough to effect your P10 panel. Fuses are good, but I selected these because my P10 is in a stand alone weatherproof box. It has many screws to seal the back panel, and would be a pain to get to the fuses. Not trying to sell you on their use, just making sure you are clear to what they are and when the may be better fit than fuses, or should be use at all.

Functions:
[TRIP]
A small current still flows through the device and is sufficient to maintain the temperature at a level which will keep it in the high resistance state. The device can be said to have latching functionality.
[RESET]
When power is removed, the heating due to the holding current will stop and the PPTC device will cool. As the device cools, it regains its original crystalline structure and returns to a low resistance state where it can hold the current as specified for the device.


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Thanks Mrgrumpy. Sounds like a better alternative than taking the box apart. I just got the Matrix Adapter today and assembled it. I also ordered the middle Strips from Boscoyo. Should get them next week. Power supply should come also.

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago
DMJPixel wrote:Here is a 3w x 4h matrix I built. I'm using Ron's board and I chained the 1st 6 panels to one output and the 2nd 6 to another. Everything mounts in base - I just have it hanging while I was working on it. Hope this helps.

Sent from my iPhone using Tapatalk

On the left side of your panel, facing the back of the panel, you have 2 ribbon cables going to Ron's board. That I understand. The ribbon cable plugged into the P10, what is that connection called. Each panel has an in and out and if I hook mine up just like that, I would be connecting it to an out.

Sent from my SM-T710 using Tapatalk


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago
mrGrumpy wrote:Maybe this FPP page will also help.

Is this looking at the back of the panels or from the front of the panels. If I had to guess I would say looking at the back otherwise the cables going to Ron's Matrix would be connected to a jout. Looking from the front the power supply should be on the right and Pi w/Ron's Matrix should be plugged into bottom row jin and third row jin on the right. Correct?

Sent from my SM-T710 using Tapatalk


Reply
Page 2 / 8
Share: