This looks like a model issue, 4 strings, 375 per string, 5 strings per strand, start ch 1 all jammed into 4 outputs alternating starting points on end of matrix. What a nightmare!!
Since you have such a convoluted set up just generate a custom model mapped as per your setup? Trying to short cut with an out of the can model is going to be tough!
Typically you try to start all of your rows from the same end, so it is even back and forth and always starting from the same end. I can see why this is a mess!
Create a custom model, 75 wide, 20 high, copy the cells from the attached spreadsheet, select the top left cell in the custom model, paste and save. Try your effects on that and see if that gets things closer.
HI joe , its one matrix and yes I have tested for individual pixels and they all worked fine
Have another thread running on ACL with some ideas which I will try, thaks for all you help everyone, hopefully progress in the near future
cheers Boof63
Matrix rejigged.
O1 1------------------>
<------------------
-------------------->
<--------------------
---------------------> 375
O2 1------------------>
<------------------
-------------------->
<--------------------
-------------------->375
O3 1--------------------->
<------------------
-------------------->
<--------------------
---------------------> 375
O4 1-------------------->
<----------------------
----------------------->
<-----------------------
------------------------> 375
This is new physical config
In xlights can get a test to run in same direction across matrix using zig zag.
Text is however upside down and appears to be offset by around 15-20 pixels in each universe. Ie text is split into each universe and then has a delay off 15-20'pixels before being displayed??
So have I wired it up as everyone else has?
If so what am I doing wrong now?
Cheers and thanks
Boof63
you appear to be 1/2 way there . In Nutcracker create your model as a vertical matrix and select the bottom left corner as start .
all should play nice when you export to HLS .Unless you are porting directly from xlights/nc to fpp .
That I can't help with .
cheers
Ok Progress -Running Bars left to right not working, Text no
Problem is the last 20 pixels of each universe ie 151 to 170 area failing to light up at all. See videos below
This applies to all universes and yes the pixels are individually fine.
Setups for pix4, NC/XL and HLs are below, any ideas please
cheers Boof63
Dropbox File (Private or Invalid)
Dropbox File (Private or Invalid)
Dropbox File (Private or Invalid)
In hls is your matrix setup as a horizontal matrix 20 x 75 and no zig zag ?
if yes , your controller zig zag should be fine
if no >
It looks like your controller is set to zig zag at 75 , if yes . try removing the zig zag on controller and test a HLS pp effect
HLS PP didn't work on HLSpreview , two separate movements, As above HLS matrix is set Left to Right, Top to Bottom .
Will try in real world to see,
Will try L to R and the R to L within HLS to see if that works
Cheers Boof63
In physical, bars move left to right, but are out of sync with colours
Do I change HLS Matrix to reflect physical setup??
Cheers Boof63
From your previous posts you are NOT using HLS to Play your Show --- so why spend time in HLS?
Get your export work with your software that is going to Play your sequence.
Remember -- In the HLS to PP channel Mapping -- if you zig-zagged there -- it will be zig-zagged in your other player.
If you zig-zagged in HLS -- your other player and your controller should NOT zig-Zag.
I suspect you have yourself zig-zagged in a knot.
Check with the people that are responsible for your Player and see what they want in the zig-zag world.
Joe
JHinkle wrote:From your previous posts you are NOT using HLS to Play your Show --- so why spend time in HLS?Get your export work with your software that is going to Play your sequence.
Remember -- In the HLS to PP channel Mapping -- if you zig-zagged there -- it will be zig-zagged in your other player.
If you zig-zagged in HLS -- your other player and your controller should NOT zig-Zag.
I suspect you have yourself zig-zagged in a knot.
Check with the people that are responsible for your Player and see what they want in the zig-zag world.
Joe
HaHaHaHa this is too funny 🙂
You took the words out that i was thinking while typing my prior post this thread .
Tip. get HLS and your matrix synced up and working perfectly before introducing NC or others.
Or vise versa if you are intending on using NC/xlights , go with that and get that working perfectly without HLS in the mix.
In my view , HLS is ...........Well you all Know what my view is !
This is my quick take on your setup the ez way in hls .
setup your controller as 4 outputs of 375 pixels > done no zig zag
in hls pixel assignment 20 rows 75 columns ( like to use my actual pixel names and numbers here ) so creating the matrix channels first and assigning each row manually makes the most sense and you get the feel for assigning exactly as you wired your matrix .
cheers
This is absolutely full proof .



