I used a similar method of slipping the strip in the soffit ledge. With the strip that I used (undersill trim), my light strips point down towards the ground. I was happy with how they looked and they are well protected from the sun and rain. I drilled small holes so I could zip-tie the led strip to the undersill trim.
Bjarmstr wrote:I used a similar method of slipping the strip in the soffit ledge. With the strip that I used (undersill trim), my light strips point down towards the ground. I was happy with how they looked and they are well protected from the sun and rain. I drilled small holes so I could zip-tie the led strip to the undersill trim.
Nice. I considered strip but I already have the bullet nodes and also didn't want to deal with the casing in strip if something had to be replaced.
I like your density though. 60 per meter?
Nice observation. I didn't realize in the close-up picture that I posted an LED strip which I didn't use on my house. I used 12V 30/10 for my house. I thought I might be unhappy with the spacing and lack of control, but cost and ease of use left me buying more of the same this year.
shows my lights in action (it was my first year)
Bjarmstr wrote:Nice observation. I didn't realize in the close-up picture that I posted an LED strip which I didn't use on my house. I used 12V 30/10 for my house. I thought I might be unhappy with the spacing and lack of control, but cost and ease of use left me buying more of the same this year.shows my lights in action (it was my first year)
Oh ok. What's the power draw on the 12v 30/10?
Video link didn't work.
Bjarmstr wrote:Nice observation. I didn't realize in the close-up picture that I posted an LED strip which I didn't use on my house. I used 12V 30/10 for my house. I thought I might be unhappy with the spacing and lack of control, but cost and ease of use left me buying more of the same this year.shows my lights in action (it was my first year)
Nice job, looks great! (link worked fine for me)
uzelessknowledge wrote:Oh ok. What's the power draw on the 12v 30/10?
Video link didn't work.
Last year I bought my LED strips from Holidaycoro http://www.holidaycoro.com/Smart-Pixel-LED-RGB-Strip-30-LEDs-m-50-Pixels-m-p/700.htm The spec says 3 amps per strip. My longest run is 30' (across the front of the garage) so it would be about 6 amps. I never tested to see if reality matched the specs. I wasn't too worried about the full white scenario so didn't need to do any power injection along that run.
Not sure why you couldn't make the link work. You can try searching bjarmstr, vimeo, monster mash
Bjarmstr wrote:Last year I bought my LED strips from Holidaycoro http://www.holidaycoro.com/Smart-Pixel-LED-RGB-Strip-30-LEDs-m-50-Pixels-m-p/700.htm The spec says 3 amps per strip. My longest run is 30' (across the front of the garage) so it would be about 6 amps. I never tested to see if reality matched the specs. I wasn't too worried about the full white scenario so didn't need to do any power injection along that run.Not sure why you couldn't make the link work. You can try searching bjarmstr, vimeo, monster mash
Thanks.
Think work is blocking it.
I did my strips in pex tube 3/4" and had my soffit installer leave the lip up a bit on the fascia wrap. He then bent me some extra white pieces that I cut into 3-4" pieces that also had a lip so I could slid my small pieces into that fascia/soffit edge there and pull it back and it would "lock" into each other like the jchannel photos above.
However, when the "mega tree" hit the house, they all had to come down and my new contractor made the fascia wrap TIGHT, so that does not work as perfectly now that I am getting them back up. The strips are going on 4 years in the pex tubing, so that has worked pretty well.
I have 41' of it and on full white I need power injection in the last 20% or so, I back feed it and that works easy enough.
The J channel in the vynil looks really well done, if I change out of strips someday ( would like more density really, so maybe go to a 60 pixels a meter vs nodes, don't know) at 41' I have 128 "nodes" of 3 pixels each, at 4" spacing that would be about the same and I would really love about 1" spacing. Be a nice way to light up the front yard too if I was out there working after hours.
uzelessknowledge wrote:Used a jig to drill the holes.
![]()
Sent from my iPhone using Tapatalk
What is the spacing you were using? I love this option
Sent from my iPhone using Tapatalk
Musicman1623 wrote:What is the spacing you were using? I love this optionSent from my iPhone using Tapatalk
Thanks. It's supposed to be 2". It came out at about 2.25". I haven't been able to get a video, but it looks great. Hanging on the house it looks so clean and blends in.



