Rite Aid led string...
 
Notifications
Clear all

Rite Aid led string question

8 Posts
3 Users
0 Reactions
2,312 Views
TMerk
Posts: 204
Topic starter
(@tmerk)
Reputable Member
Joined: 12 years ago
[#39097]

I bought a 100ct string of white led's from right aid, plugged em in and they had a severe flicker. I put a fwc on them and it made a noticeable difference but they still flicker. There is no blob of any sort and I checked the continuity of both plugs and it has cont. in both directions. Can these be really cheap lights and have no rectification at all? I did a bunch of walmart strings with 100% success.


7 Replies
Posts: 66
(@mrsmith)
Estimable Member
Joined: 12 years ago

There are manufacturers in China that will make 120v non-rectified led strings so their customers can save a little more money. I received samples from one that were similar to what your talking about but they didn't flicker to bad. Here is some pictures when I dissected them just to make sure they were LED. I tore apart both plugs as well and no rectifier.

image
image
image
image

Reply
TMerk
Posts: 204
Topic starter
(@tmerk)
Reputable Member
Joined: 12 years ago

Looks almost exactly what I have except mine are green wire. They weren't cheap at rite aid either. Glad I only bought 1 set.


Reply
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago

Do half wave LED strings always need an external rectifier? After all, they are themselves diodes, within the reverse voltage spec.

For example, if you have two segments of 50 LEDs in series, and each LED had a 5v reverse blocking rating, that would mean they could handle 250V reverse without conducting, which is higher than the roughly 180v peak of 125VAC.

Of course they always need a resistor, so if there is a single blob in series with the LEDs in each segment, it could be the resistor rather than a diode.


Reply
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago

As to flicker - do other people perceive them as flickering? Some of us seem to be more bothered by flicker than others.

I just posted another thread where I was reasoning that more LEDs per series segment would imply that they would conduct for a smaller portion of the half cycle of AC (see graphs there). If the combined Vfwd of the LEDs was fairly high, and your AC voltage fairly low, this could create very short pulses of conduction.

But I would think this should be less obvious than the difference between full and half wave LED strings, where for half wave the off time is 2/3 or more of the full AC cycle. I would imagine that two short pulses per cycle (when you externally HWC's the string) should be less visibly flickering, than any half wave string.

LED half full

And most 50-series-segment half-wave LED strings look OK to people. So I'm not so sure this explains an especially visible flicker in you RiteAid string. Still, out of curiosity, how long are the segments? (how many LEDs between where the wiring goes back to two strands?)


Reply
TMerk
Posts: 204
Topic starter
(@tmerk)
Reputable Member
Joined: 12 years ago
And most 50-series-segment half-wave LED strings look OK to people. So I'm not so sure this explains an especially visible flicker in you RiteAid string. Still, out of curiosity, how long are the segments? (how many LEDs between where the wiring goes back to two strands?)

33+33+34


Reply
Posts: 1076
 Zeph
(@zeph)
Noble Member
Joined: 15 years ago

I'm wondering if there is a manufacturing defect of some sort (versus a design problem per se). Puzzling.


Reply
TMerk
Posts: 204
Topic starter
(@tmerk)
Reputable Member
Joined: 12 years ago

I agree 100% on what you are saying, especially with less than 50ct per segment. You would think there would be less flicker but not in this case, they almost look like fast firing strobes! lol I think you are right about the defect. I'll just keep using the known brands when budget allows, buy the full wave. Thanks for your input.


Reply
Share: