I am in the process of converting candy canes(similar to the ones shown in the how-to in the wiki) from the stock lights to LED rope light. I had purchased a 150' spool of cool white rope light from CDI and had thought that I was just going to run 110v to a 36" piece with a bit of spt2 and vampire plug and all would be well. When I opened the box today to begin the project I noticed that the five power cords that were sent with the 150' spool all had 1.6 amp rectifiers built in. I went ahead and cut a 36" piece and hooked it to the supplied, rectified power cord and then made a 36" section with the spt2/110v method described above just to see what the difference would be. The rectified piece looks fantastic, the 110v piece looks terrible(flickery/50% less bright). My experiment proved to me that I cannot get away without rectifying these 36" pieces. This is where the problem starts...
I have 20 candy canes to do...and I was supplied with 5 of the cords with built-in rectifiers. You can buy them here http://1000bulbs.com/product/56552/SIV-F106.html but they are $7.35 each plus shipping. $7.35x15= over $110...not gonna happen.
My question to you wonderful folks....what are my options here? Can I make a rectifier? Buy a pre-made rectifier that would work to add in-line to spt2?
PS ~ These will all be individually controlled so putting all the candy canes on one rectifier cord won't work, unfortunately.
Thanks for any help you can offer.
I modified some snowflakes earlier this year and added rectifiers In the process. I just used a common 400v 1a bridge rectifier in the round package with all four legs coming out the same side. I think they were like 30 cents each at mouser. It was overkill for my project as i only had 17ma going thru it. (15 leds in series) I soldered the spt2 directly to the AC legs and I think it was 20awg wires from the light circuit to the DC side. I heat shrinked each connection and then put the whole thing in another heat shrink. It's not the best mechanical connection but with the right strain relief it seems to be just fine.
--Jon Chuchla--
Sent from my iPhone using Tapatalk
jchuchla wrote:I modified some snowflakes earlier this year and added rectifiers In the process. I just used a common 400v 1a bridge rectifier in the round package with all four legs coming out the same side. I think they were like 30 cents each at mouser. It was overkill for my project as i only had 17ma going thru it. (15 leds in series) I soldered the spt2 directly to the AC legs and I think it was 20awg wires from the light circuit to the DC side. I heat shrinked each connection and then put the whole thing in another heat shrink. It's not the best mechanical connection but with the right strain relief it seems to be just fine.--Jon Chuchla--
Sent from my iPhone using Tapatalk
So I could use something like this? http://ca.mouser.com/ProductDetail/Rectron/RB154/?qs=sGAEpiMZZMtcLAek5QF0i83Wd050yT7yrEmtaem129w%3d
1.5a is way overkill, I will be pulling enough amps for a 36" stretch of rope light....but it is what the stock ones are(well 1.6a) and they are only 0.31 each.
That looks just like what I used. Worked for me!
--Jon Chuchla--
Sent from my iPhone using Tapatalk
I just pulled the in-line rectifier on one of the factory power cords apart and found the equivalent to this http://www.mouser.com/ProductDetail/Rectron/BR610/?qs=sGAEpiMZZMtcLAek5QF0i83Wd050yT7yR%252b4KcZ6VTQ8%3d inside. I could just order 20 of these and keep it the same as the factory spec, but at $1.40 each that is more than 4x something like http://ca.mouser.com/ProductDetail/Rectron/RB154/?qs=sGAEpiMZZMtcLAek5QF0i83Wd050yT7yrEmtaem129w%3d . Anybody see any pros/cons/reasons why I should go with the 1.40, heftier rectifier rather than the smaller and much cheaper ones? It would ultimately be a cost savings of about $15. Again these will be rectifying a 36" piece of 1/2" led rope light.
Thanks,
Eric
