Pixel (GECE) string...
 
Notifications
Clear all

Pixel (GECE) string mystery

9 Posts
4 Users
0 Reactions
2,725 Views
kk6ou
Posts: 108
Topic starter
(@kk6ou)
Estimable Member
Joined: 10 years ago
[#47992]

I am running a couple of strings of GECE lights with a Falcon F16V3 controller and a RPi. All was well for a week or so and then I had about 10 lights go out in the middle of one of the strings. The odd thing is the nodes that went out are all sequential in the middle of the string of 50. I tried the display test mode and they all act as dead. My confusion is if this was a light not sending data I would think that all the lights after it would be dead not just 10. I have the power supply at the beginning of the string so no voltage drop. I'm running about 12' of Cat6 for data from the Falcon to the string. The two strings are on different ports, not tied together, and only one string has this issue. Has anyone seen this happen before? I'm not sure if it's related to GECE.


8 Replies
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

power cycle the string and controller at the same time. Leave it off for at least 30 seconds before powering back up. Make sure the string is powered up before the controller starts sending data to it.


Reply
Posts: 127
(@lostbucket)
Estimable Member
Joined: 9 years ago
jchuchla wrote:power cycle the string and controller at the same time. Leave it off for at least 30 seconds before powering back up. Make sure the string is powered up before the controller starts sending data to it.

As he said.... you might of sent data at one point then applied the power and those set of pixels could of read it's instructions and got to much power and burnt the pixels up. I hope that's not the case.


Reply
kk6ou
Posts: 108
Topic starter
(@kk6ou)
Estimable Member
Joined: 10 years ago

I'll have to take a look tonight when I get home. I've already removed them from the display but I can drag them out and hook it all up again. It's possible that I did that in testing. I never knew that it made any difference on when you applied power vs data.


Reply
jchuchla
Posts: 8698
(@jchuchla)
Illustrious Member
Joined: 15 years ago

The actual reason is because GECEs are actually addressed pixels. They're the only type that works this way. (that i know of at least) They set their own addresses from the first data it sees when the pixels power up. So you need to make sure the first data the pixels see is in order from 1 to 63.


Reply
kk6ou
Posts: 108
Topic starter
(@kk6ou)
Estimable Member
Joined: 10 years ago

Thanks for that info. That makes more sense on how some can be out in the middle of the string. I'll be happy and ticked off at the same time. Happy if they aren't out and ticked because I ran the display with them like this when I could have fixed it. I'll probably replace them with regular pixels like Brilliant Bulbs.


Reply
Posts: 1168
(@keith-r)
Noble Member
Joined: 19 years ago

I also tried running my GECE's off of a F16V2 (updated) and never could get the GECE's to run. They worked fine off of an e682, but finally gave up and left them out of the show. I want to keep them because of the ease of setup on the garage. Will do more testing this year and ping Dave to see why they wouldn't fire up.


Reply
kk6ou
Posts: 108
Topic starter
(@kk6ou)
Estimable Member
Joined: 10 years ago
Keith R wrote:I also tried running my GECE's off of a F16V2 (updated) and never could get the GECE's to run. They worked fine off of an e682, but finally gave up and left them out of the show. I want to keep them because of the ease of setup on the garage. Will do more testing this year and ping Dave to see why they wouldn't fire up.

My main reason to use them is the F16V3 supports them quite well and I had them from my previous years of static display. Other than the problems I mentioned above they worked pretty well. I hadn't used 5V pixels before and found that I had to inject power right at the string. I tried running 12AWG cable from my controller but found the voltage drop was too much trying to run over 10'.

They look nice but as I said I will probably replace them with Holiday Coro Brilliant Bulbs which is what I'm using on my roofline. I also might consider Ray Wu if I decide to order a lot more lights to get the shipping down.


Reply
kk6ou
Posts: 108
Topic starter
(@kk6ou)
Estimable Member
Joined: 10 years ago

Got home and tried out the lights again. Yep, You need to apply power before sending data. I think I messed them up when testing by recycling power while sending data.
Thanks for the advice! I'll probably replace them anyway for this years show.


Reply
Share: