Just finished building one of my DIYC floods and thought I'd share what I did. I'm still waiting on a 15V PSU to test it properly (using a PC PSU as a bench supply right now which is only 12V).
I still need to share some photos on how I mounted things but ended up using one of these as an enclosure, which I think is the typical one to use. I removed nearly everything that was inside and all the AC wiring along the back and bottom.
I mounted a Ren4Flood behind the LED board and used clipped leads from components and wired the two boards together. Then I used M3 screws and standoffs (available here).
I ended up making the standoffs a bit tall so the RJ45 jacks would not be obstructed. I drilled screwholes in to the back of the enclosure and just ran nylon screws through into the standoffs. I then used some spare connectors I originally bought for building a paraboard to charge some RC batteries and ran one out the hole that the original wires of the enclosure were fed through. One minor issue is that an RJ45 obviously can't fit into that hole, so my the next go-around, I may wire up a female jack out the back. For now I just cut some cable and crimped the RJ45 on the other side after running it through the whole.
After doing all that, perhaps the most important step was I cut out some rice paper and mounted it to the inside of the glass making a diffuser that works surprisingly well, at least in my tests so far. The RGB white now looks a lot more like actual white instead of a rainbow and color mixing is better. Not as good as true RGB LEDs but should work quite nicely.
Anyways just thought I'd share.
Pls share images of the diffuser, and if possible before/after shots of the colour mix. I'd like to see the differences.
I plan to, though wanted to test driving the LEDs at full brightness first. I had some extra rice paper lying around I wasn't using, but tracing paper may work just as well. If you're looking at the flood itself, you can still see the individual colors, though thrown up at least in my office wall, it looks a lot better.
PSU should be here in a few days. I ordered the one recommended off the wiki and plan on taking build photos then.
Fluorescent diffusion panels work great as well if its something you're looking directly at. I tried a few and went with the "cracked white ice" one on my columns:
Originally I used the "cracked ice" panels for the diffused on my LedTricks, but found that after 2 seasons, it had become extremely brittle and cracked. UV? Cold? I don't know, but I then replaced it with a semi-translucent corrugated plastic. Can still see some lines from 5 ft away, but from 20 feet away (and in the dark), it works brilliantly. I was considering adding these to my led floods (bringing this back to the thread topic), but was concerned about it being too much diffusion.
Oh finally got some photos for folks. The photos of the bare boards is mostly correct only I stack some standoffs when in the case so that the board sits high enough to be able to plug the cable into the RJ45 jack. Otherwise hopefully that shows it. I'll try and get some video going so folks can see how bright it is. Using 15V+ it does indeed get pretty bright - I'm hoping 2 of these should be good enough for my rather small porch.
I used THIS case to install my DIYC floods under the eaves - it has a clear top but probably not a bad idea to scuff them up a bit to diffuse better - - may have to do that (I have 12 installed). They can probably fit a Ren4Flood in there as well but I'm using a Ren48LSD.
Well that's a clever way to do it! For my setup, putting them on the ground should be fine for at least this go-around since you can't see the bottom of my porch easily from the street (covered up by some bushes, which will also have their own lights). Thought I won't really know until I test it on my actual porch. I'd do that now but don't have a great way to run test patterns or anything with the flood lights just yet.
m00dawg wrote:Well that's a clever way to do it! For my setup, putting them on the ground should be fine for at least this go-around since you can't see the bottom of my porch easily from the street (covered up by some bushes, which will also have their own lights). Thought I won't really know until I test it on my actual porch. I'd do that now but don't have a great way to run test patterns or anything with the flood lights just yet.
Oh yeah - I have some of the same yellow enclosures you have as well for ground level stuff - also have the Utilitech red ones which are pretty nice to use as well. Just make sure you get the front covers on good. I found one completely full of water (still running fine!) after I shut down the show. Unfortunately - while still working somehow (it was a MightyMax, not DIYC Flood), it was so corroded up, I had to toss it... If the lids shut down instead of up, it would help.
Indeed, I was thinking of using at least hot glue over the hole where the cables come out and maybe hot gluing the top as well. Since they'll be under the porch, it's pretty well dry in there even with hard rains so I"m not too worried this year. I do like the ffect though so I bet I'll end up using them in other places maybe for the 2016 show.
My bigger water woes are my RGB coro-trees and my pixel tree. They will be in the elements for sure.




