Notifications
Clear all

Pixel Plane problem

41 Posts
6 Users
0 Reactions
13.2 K Views
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

I can tell by your screen cap that something is not right , as the text lines are 1 on top of the other

there is no yellow in the effect

1 text string is red and the other is green

I think your preview Group config is wrong > just my guess though


Reply
Posts: 825
 DanJ
(@danj)
Prominent Member
Joined: 13 years ago

Thanks for the info. This is "somewhat" similar to what I did for Christmas 2013; I setup my NC effects then dropped them onto the appropriate channels in LOR S3. What I was interested in finding out is--how do you "normally do business"? Do you do most of your RGB effects "inside" HLS? Or do you do your effects in NC then drop them into HLS? Just wondering... Thanks.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

I do most of my mega tree and matrix effects in Adobe After effects then export/import into HLS .

arches and the house matrix are all done within Hls built in PPeffects generator.

The beauty of HLS is that you can import and export along with edit so many variants it is staggering

How Joe has enabled this amount of user control .

I should really do a .doc that lists and demonstrates all the capabilities .

Here is a few <>

import : lor, nutcracker ,png ,vixen,

export: png , nutcracker, PP effects


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Carl

Santacarl has exceeded their stored private messages quota and cannot accept further messages until they clear some space.


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago

With grateful thank you's to Angus40......without whose help I would still be lost....

IT WORKS....IT WORKS.....IT WORKS.... :arrowr:

Well.......I discovered a couple of tricks that might help some other lost soul in the future.

1. When you create a MT that's larger than 180 degrees....you have to add channels to your preview to complete the remaining degrees where there no 'actual' lights.....but don't assign them...... That part I understood. But what I did NOT understand is that you have to add DUMMY channels using the Manage Channels tab.....and assign them preview group numbers (later deleted after building the preview) so that you can use them in the preview to create the 'dummy channels' on the unused degree area that's used to fill out the virtual model.....I used your model and created a second tree to assign the additional channels to......

2. Do NOT under ANY circumstances use old Preview Group channel order numbers unless you clean them up first....

This year when I added the MT...I loaded a channel layout from last year's show to start the sequence with and then added extra channels in order to make come up with my mega tree.... That was fine....

I then used just added on to my existing preview from last year.....BIG MISTAKE..... No matter what I did...or how many times I rebuilt the preview following along with Joe in his video I could not get preview to work correctly......

Finally just as I was about to throw in the towel it crossed my mind that I should try a new sequence/clean model.....with just the MT. It worked the first time!

I went back to the full model and re worked the preview yet again.....same failure.

So after scratching my head for a bit.....I renumbered ALL of my preview Group numbers.....carefully putting them in order and leaving no blanks (had some channels that weren't used in the old preview)

I went back and BOOM...it worked like a charm..... :yay:


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

Once you get a good grasp of hls you will find all kinds of tricks and short cuts.

Then you will realize just how powerfull hls is .

I have been playing with HLS for the past 2 years and still do not use 1/2 of the features , I'd really like to learn the face animation stuff but do not have the

storage space in my brain or the patience to tackle the learning curve.


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago

I've had the face animation idea in the back of my mind for a while......once I learn to "walk".....I might play around with it.....


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

The facial animation is probably the simplest thing to learn in HLS, it was the single reason I adopted HLS as my 1st sequencer last year.
Once you sit down and start a song, inside of an hour you will have it mastered!
Now, doing facial animation using a pixel MT is another story (haven't done it yet). Habbosrus has a handle on that and has done a few songs that look great! I am going to give that whirl this year along with a rope light 6ft talking tree.


Reply
Posts: 159
(@christmasgeek)
Estimable Member
Joined: 13 years ago

With pixel and facial animations, personally I've found it easier to draw them out (I created a graph for mine of 1800 dots) so I can write drown their location before assigning to mouth or eye positions. If anyone is interested I'll share what I have when done (I've redesigned my matrix and mega tree for the last time).


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago

I'd love to take a look at the idea.... I'm learning and find that having different techniques in my toolbox is a big plus....sometimes 1 way of doing things works better in certain situations than another.....

Christmasgeek wrote:With pixel and facial animations, personally I've found it easier to draw them out (I created a graph for mine of 1800 dots) so I can write drown their location before assigning to mouth or eye positions. If anyone is interested I'll share what I have when done (I've redesigned my matrix and mega tree for the last time).

Reply
Page 4 / 5
Share: