Notifications
Clear all

Output order ?

13 Posts
4 Users
0 Reactions
7,098 Views
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
[#34285]

Hey light junkies!

This year I eliminated some controllers and their cooresponding 96 channels. I basically eliminated them from HLS but didn't change the output order of the remaining channels. Just an oversight. So my outputs go from channel 1-264 then skip to 361 and pick up again.

This doesn't seem to be an issue for HLS. Am I correct in assuming that?

So my question is really about my Pi Player and the output order coming out of HLS. I have a couple of sequences where my MT effects start on the wrong row on the tree.....Could my output order in HLS be a mismatch with the Pi? It only does this on a couple of sequences....the other sequences work perfectly. These couple of sequences, when played back using HLS to output to the display, work fine..... Apparently when the conversion from HLS to the .fseq file takes place...there is a mismatch some place....

Thanks


12 Replies
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

what happens if you leave the channels in place and just remove all sequence data ?


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
angus40 wrote:what happens if you leave the channels in place and just remove all sequence data ?

Sorry Richard....I'm not following the logic..... Are you suggesting just wiping out all the sequence data and run a 'blank' sequence?


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

just remove the sequence data from the channels that you want to delete , rather than deleting the channels .

Just a suggestion to see if every thing plays correctly .


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
angus40 wrote:just remove the sequence data from the channels that you want to delete , rather than deleting the channels .

Just a suggestion to see if every thing plays correctly .

Oh.....too late. The channels were already deleted....I just left the output order as it originally was set with those extra controllers.

So in my output order I just have a gap....they are still in order as the channels deleted came out of the middle in a chunk.....so in essence when I go from universe 1 (last output channel # is 264) to universe 2 I skip to output channel #361 as my next channel....

As I said earlier it doesn't seem to bother HLS....I'm just trying to decide if that output order is confusing the Pi.....


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago

It is never to late with HLS 🙂

You could simply ( for test purposes ) load a saved version of the sequence > before you deleted the channels .

try that exported without the sequence data on said channels and see if that resolves your Fpp dilema .

best I can suggest .

cheers and good luck .


Reply
Posts: 2048
(@scootchu)
Noble Member
Joined: 17 years ago

If you're feeding a Renard you place a Fixed DMX channel in the box where your channels pick back up.
165

225 Fixed DMX 225

You can have Ren 64's with just 20 channels being used as long as you note where the next board picks it back up via Fixed DMX. On the conversion side it's all done for you just set up your universes like normal.


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
scootchu wrote:If you're feeding a Renard you place a Fixed DMX channel in the box where your channels pick back up.
165

225 Fixed DMX 225

You can have Ren 64's with just 20 channels being used as long as you note where the next board picks it back up via Fixed DMX. On the conversion side it's all done for you just set up your universes like normal.

Actually....the next board is an E682.....on a new universe...but I don't know if universe is the issue.....or if channel output number is....


Reply
Posts: 3650
(@jhinkle)
Famed Member
Joined: 15 years ago

Within an E131 message packet for a specific Universe -- there can be no gaps in channels -- needs to start at channel 1 and end at what ever channel it ends at --- BUT --- no gaps in channel numbers at the start or in the middle of the Universe.

Joe


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
JHinkle wrote:Within an E131 message packet for a specific Universe -- there can be no gaps in channels -- needs to start at channel 1 and end at what ever channel it ends at --- BUT --- no gaps in channel numbers at the start or in the middle of the Universe.

Joe

So.....universe 1 output ends on channel 264.......Universe 2 output starts on channel 361...

There are no gaps in output order in either universe....just between them

Is that OK or is that 'verboten'?

Thanks Joe....


Reply
Page 1 / 2
Share: