After you build the tester, you can use the other end of the cat5 cable you cut to help test the SSR. If you hook pin1 from the SSR to +5v and pin7 to gnd you should be able to hook any of pins 2,4,6 and 8 to gnd also and turn on the strand of lights connected to that output.
This is assuming you are using co-op boards.
RickeyS wrote: With using an external power supply I don't need a shunt on J1, correct?
Thanks
Rick
Rick, correct, when I was building my GRINCH, Wjohn told me that the shunt has to be on for two scenarios; 1) power coming in via Pin 1 on the RJ45 IN, or 2)to pass power out RJ45 OUT to a second board.
Note that if you are bringing power in on pin 1 on the RJ45 you would still need to provide the power source from other than the parallel port.
The parallel port DB25 has Gnds on pins 18-25, you only need to take one of the Gnd pins to #3 of the RJ45. It is ‘being safe’ to take more than one pin across on the ground. The idea is that your reduce the resistance of the connection by have more than one Gnd pin connected in parallel.
Since you have an external power supply going to J2, you only need the shunt if you are connecting another board.
I will try the tester, but another quick question, the desktop I'm using is running Vista does this matter? Also when I get home I'll try to run from my laptop and see it that works, If not it will be the tester and start to narrow down if it's the grinch or SSR.
Again thanks and please keep the suggestions coming on things to try, I'll also try to get pictures of my grinch and ssr to post.
Rick
What are you using for your power supply?
scharbon wrote:Problem here is trying to trouble shoot two components (Grinch and SSR). When I built my Grinch I made this tester from computer Christmas (Go to the lAst page and see photo at Step 7). Plug it into any port in the Grinch and see if the LEDs turn on with various channel combinations. If they do, then you know the problem is the SSR.Lets try to isolate which part doesn't work.
Steve
thats an awsome little tester,
should get that added to the wiki.
also with the parallel port try different settings. epp didnt seem to work for me. try the other settings.
also maybe your power supply is to high. from what i hear some of the guys have had to adjust the supply down to about 4v to get it to work.
can you adjust the power supply for the grinch at all ?
What I'm using for a power supply is a hard drive adapter, Its one with a +5vdc and a +12vdc with a ground. Its used to power an hard drive that's not in a computer. It is regulated and I did check at the Grinch it has 4.84 volts.
Thanks
Rick
How would you go about adjusting the power supply? I'm at work now but will try all this tonight when I get home.
Thanks
Rick
rick, do you have any power diodes? 1n4001 or similar? you could put one inline with the grinch and it should drop it about .5v.
put it on the +5v line, but you might have to work out which way it goes as it will only work 1 way.
other than that a dedicated power supply might be needed.
Peter
RickeyS wrote:the desktop I'm using is running Vista does this matter?
Rick
I thought Vixen doesn't work with Vista :confused:
It does work with Vista 32, just not enough users to make sure all of the bugs are worked out. Its the VISTA 64 bit version that is not supported.
Some guys ran Vixen on Vista 32 for Christmas 2007. Didn't have any problems.
I PM'ed KC on this issue last year because I bought a new computer (Vista) and wanted to know if it would work. He wrote back that is did in fact work.
I didn't use it after all because my new computer had no parallel ports and the only serial port was tied to the monitor. So I fired up the one that was about to go to the recyling center and it has become my show computer.
Steve
