I have been going round and round on this software question. Looking at the different softwares and trying to figure out which way to go and or if I'm not ready to make the leap. Let me give some background and spell out what I am planning. Last year I ran a total of about 288 channels, 3 Ren64, 3 Ren24, and a Ren24LV. I did not use all of my channels but most of them. I have had eight, 7 channel arches in my display for several years, they are made from 100 count blue incandescent strings and they are showing their age. My plan is to replace the incandescent lights with RGB Pixels. I am looking to go with a 50 pixels string per arch. That would be a total of 400 pixels and 1200 channels. My guess is that I will get an e682 board to drive the pixel strings. I don't know if I will get an RPM for the Renard boards, I am guessing that will depend on which software I use. So, the plan is to take away 56 channels and replacing them with 1200.
I am also planning on adding a LEDTrix with a TrixC this year. I know that is also a different output. I know I can do LEDTrix programming in Vixen but not sure about HLS. I've played a little with HLS but it seems to be a bit tedious to work with. I have troubles getting copy and paste to work in HLS. Maybe it's the fact that it is new, but I am not sure yet how the output works in HLS, how do you configure it for different boards? Since I will be using a mix of outputs, Renard, E1.31, and LEDTrix, which software will handle these with ease. Here are some bullets of what I know and want, maybe this can give you enough info the help throw your opinion in this question.
- I know and like Vixen 2.5
- Like having a Profile that the sequences use, have needed it to change channels for miss wiring or bad channels
- What can handle LEDTrix and TrixC
- Have not tried Vixen 3 yet, what does it bring to the party?
- I think HLS will handle the RGB element of my show does Vixen 3?
- Have not tried Nutcracker yet, as I understand it can output to either HLS or Vixen
- Have a low power single processor show computer, does that make a difference with pixel
This may not be all but it's a start. I am not looking for a final solution right not, I am looking for your suggestions and why. I know my setup is not unique, some of you out there must be running something close to it. I don't know enough right now to make an informed decision. I am also trying to see which way to go based on budget, it seems to be tight this year. I am wondering if I am trying to do too much. Maybe upgrade my arches next year and give RGB software another year to improve. Maybe just work on the LEDTrix for this year. I just need to get some more info to know how and or if this can be done.
Thanks in advance for your inputs.
mikeh65 wrote:I am also planning on adding a LEDTrix with a TrixC this year....
- What can handle LEDTrix and TrixC
...
Mike:
I'll leave it to the various software partisans to sing out the praises of their favored applications.
But on the LEDTrix and TrixC, you don't need to worry: None of the applications actually drives them.
Originally, the LEDTrix was driven directly by Vixen 2.x but when TimW built the TrixC, he created a driver application specifically for it (the idea behind the TrixC was to take the huge burden off a PC and put it onto a small, cheap card).
You do use Vixen to create the LEDTrix/TrixC message/design, but you then take that file and execute it through a command-line application called LTC.
I have batch files set up to execute at different times during the night to change my LEDTricks' message and Vixen is never involved. In fact in 2011 (didn't do a show in 2012), I used xLights to run the show and it co-existed with the batch file with no problems, so Vixen wasn't in the mix at all.
Here's a single thread that explains (most) of the TrixC environment:
Triks-c-Putting-it-all-together
HTH.
\dmc
