Triac Checking Circ...
 
Notifications
Clear all

Triac Checking Circuit?

11 Posts
3 Users
0 Reactions
3,316 Views
Posts: 15
Topic starter
(@aggiewonder)
Active Member
Joined: 15 years ago
[#28870]

After finishing assembling an SS24, Channel 1 failed to turn off during testing. Deciding to look ahead before proceeding to replace Triac #1, I measured Channel 1-24's output voltage with no optoisolators installed. I'm sure routine basic questions arise. This is not my first board, been soldering for over 20 years, back of board was scrubbed, cleaned, and solder joints inspected. Here's what I found (all AC voltages):

1 112
2 83
3 9.3
4 8.7
5 9.1
6 9.1
7 8.8
8 120
9 9.0
10 8.3
11 9.3
12 11.1
13 10.2
14 13.9
15 120.3
16 118.5
17 8.9
18 119.5
19 32.9
20 9.1
21 9.2
22 64.1
23 11.2
24 19.2

So, with no optoisolators, it looks like I have at least 6 bad triacs (channels 1, 2, 8, 15, 16 & 18) and two questionable triacs (19 & 22).

I understand getting some bad components in this kit, but a 25% failure rate seems questionable. So, does anyone test their triacs before soldering them in the board? I.E. Use the diagnostic firmware with an eight channel "test circuit" to verify operation before installing them?

Any ideas? I can't imagine receiving this many bad triacs, but I'm sure it happens. Still hard to imagine...


10 Replies
Wayne J
Posts: 7789
(@wayne-j)
Illustrious Member
Joined: 19 years ago

Something else is amiss or others would be having the same issue. A defective rate of that percentage in a single kit is not normal.


Reply
Posts: 15
Topic starter
(@aggiewonder)
Active Member
Joined: 15 years ago

I agree...but I sure can't find it! At least Channel 3 works with a string of lights! Yay!


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 19 years ago

Have you tested the channels using a real light?

It takes only a little bit of leakage through the triac for a volt-meter to show a high voltage, as the input to the volt-meter is high-impedance. It may very well be that the amount of current leakage on your 'bad' channels would be so low as to not cause a problem.


Reply
Posts: 15
Topic starter
(@aggiewonder)
Active Member
Joined: 15 years ago

Interesting read:

http://www.epanorama.net/circuits/semiconductor_relays.html

RE: Testing-->

"How can I test my SSR?
It is not possible to test an SSR by the same methods used to test mechanical relays; a typical SSR will always show an infinite impedance to a resistance meter placed across the output terminals. To test an SSR, it is best to operate it at the actual line voltage it will be used at, driving a load such as a large light bulb.

The load turns on okay, but never seems to turn off, unless I remove power from the relay entirely. What might be happening?
This is normally a problem when using an SSR with a high-impedance load, such as a neon lamp or a small solenoid. Loads like these often have relatively large initial currents, but relatively small hold in currents. The result is that the off-state leakage current through the relay (see previous section) is insufficient to cause the load to turn on to start with, but sufficient to keep it on, once started. The solution to this is to place a power resistor, sized for 810 times the rated maximum leakage current for the SSR in parallel with the load."


Reply
Page 1 / 3
Share: