ss8 com troubles
 
Notifications
Clear all

ss8 com troubles

11 Posts
4 Users
0 Reactions
4,558 Views
Posts: 528
Topic starter
(@bud29)
Honorable Member
Joined: 17 years ago
[#17309]

OK,

Done with wiki, on to the experts:

I've got an SS8 that does not seem to want to communicate. it is 3rd in the chain, 1st is a ss24, 2nd is a ss8.

The cable, vixen setup is denifintely good, I can put in another controller and it works fine. I've run the diagnostic firmware and that runs as per the wiki. I've tried replacing U5 and reflowing the solder joints for U5, the RJ45 connector. Nothing seems to help. What am I missing?

Rob


10 Replies
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Couple common things to check:

1. How many channels are in your profile? Should be 40 (or however many channels you have)
2. How many channels is your Renard modified plugin set to manage? Should be 40 (or however meny channels are to be controlled with it)


Reply
Posts: 528
Topic starter
(@bud29)
Honorable Member
Joined: 17 years ago

Channel counts are good. I can remove the problem SS8 from the chain and put another controller in it's place and te replacement controller works fine, so the issue is definitely in the SS8 itself.


Reply
RavingLunatic
Posts: 1502
(@ravinglunatic)
Noble Member
Joined: 19 years ago

You say that the board passes diagnostics, which means:

1 - Channel test works
2 - HB and ZC blink after the Channel test
3 - When VIXEN data is sent, the SD LED is on and FE and OE are off

Correct?

Does the board react differently when connected as first in line?


Reply
Posts: 528
Topic starter
(@bud29)
Honorable Member
Joined: 17 years ago
RavingLunatic wrote:You say that the board passes diagnostics, which means:

1 - Channel test works
2 - HB and ZC blink after the Channel test
3 - When VIXEN data is sent, the SD LED is on and FE and OE are off

Correct?

Does the board react differently when connected as first in line?

1. yes
2. yes
3. when data sent, all SD, FE and OE all are off.

Board reacts the same if first in line.


Reply
rstehle
Posts: 4348
(@rstehle)
Illustrious Member
Joined: 19 years ago

Have you tried reflashing the PIC?


Reply
Posts: 528
Topic starter
(@bud29)
Honorable Member
Joined: 17 years ago

yup, tried reflashing several times.


Reply
RavingLunatic
Posts: 1502
(@ravinglunatic)
Noble Member
Joined: 19 years ago
bud29 wrote:

3. when data sent, all SD, FE and OE all are off.

Then you are not getting data to the PIC, so diagnostics did not pass.

- Swap U4 and U5

- Use the schematic in the wiki and double check continuity between the output of U5 and the PIC.

- Check the solder joints on U5, the PIC and resistors and diodes for the COMM circuitry

- Check the RJ45 connector J2 to make sure it is making good contact

- Make sure you didn't leave JP1 installed

If after all that you still have issues, then use a good board and start comparing voltages on U5 and the PIC when data is being sent.


Reply
Posts: 528
Topic starter
(@bud29)
Honorable Member
Joined: 17 years ago

Had already tried swapping u4 and u5, no luck
continuity good from pin1 on U5 to pin5 on U6
checked solder joints and reflowed, no luck.
rj45 j2 looks good 2 me
jp1 not installed.

I'm starting to need a stiff drink.


Reply
Posts: 528
Topic starter
(@bud29)
Honorable Member
Joined: 17 years ago

With data being sent, U5 has following voltages:

pin 1 - varies 0 to .22vdc
pin 6 - varies .15 to .3vdc
pin 7 - varies .9 to 1.8vdc


Reply
Page 1 / 2
Share: