flicker fixes
 
Notifications
Clear all

flicker fixes

83 Posts
34 Users
0 Reactions
50.2 K Views
corytcline
Posts: 1249
Topic starter
(@corytcline)
Noble Member
Joined: 16 years ago
[#17307]

Due to all the flicker problems I have been experiencing and reading about, I thought I would start this thread for everyone to post there fixes in. Hopefully having all the fixes in one thread will help others having problems find a fix quick.

I managed to get most of my flickering out with snubbers on all of my led channels. I made them with:
1w 47k 5% KOA Speer metal oxide resistors mouser part #660-MOS1CT52R473J.

I soldered the resistors to male plugs that I cut off the cords I used for the renard's seperate channels.
I wrapped them tight with suran wrap and tape and plugged them into the end of the last string of led's on each channel with led's.

My power cord and most of my channel cords are coiled as well. Not sure if coiling the cords made much of a difference but it seems to have worked for others. I can say it made a HUGE difference when I coiled the power cord to my FM02 transmitter, so there may be something there.

My setup is simple I have one renard ss 24 connected to my cpu with a usb to db9 adapter.


82 Replies
klyneshouse
Posts: 230
(@klyneshouse)
Reputable Member
Joined: 16 years ago

Not 100% corrected but these things helped clean 90% of it. - (listed in order tried, not by effectivness)

1- ensured all my SS boards were all lined up on the same 120/Neutral from the breaker box. Criss crossing these seemed to make this much worse.
2- Added snubbers, glade/renuzit plugins @ 9.2 K ohms to every 120 led channel.
3- Seperated distance of contollers, power cords as much as resonably possible.
4- dunnsr reccomendation of surge protectors... http://www.walmart.com/ip/Philips-1-Outlet-Surge-Protector/17127162#Specifications

5 - Made family quit using microvave- (xbee proximity issue/unrelated) :blush:

Unfortunately I still had to remove sequecing some exotic 96 channel "candle flicker" from one song as all the others were off and it was just too obvious.
I tried this again after all fixes and its just too much still.

weird observation for me -
I am divided into 5 seperate wirelss zones on 5 seperate breakers.
Every night it seemed like one ramdom zone was the worst, while others may be flawless, and then the next night they are the worst.
I mentioned early i had one zone using older boards that were not exibiting this, after not applying the surge protectors to that zone and everywhere else, it is now the problematic one.

setup specifics requested below:
It only happens when something else gets ramped up or down.
50ms, 57K Baud, broadcasting from single xbee explorer.
Changing sequence timing to 100ms & 200ms or playing at 1/4 speed still produced same results.
mostly half wave leds intalled past ch 48, but both incans and leds seem effected equally from a generation or receiving standpoint.
96 ch of incans are single C7 bulb, in Zone 2,3,4.

Wireless Zone 0 - RENW4X (ch 23 & 24 )
WZ1 - 2 x 24SS ch1-48
WZ2 - 2 x 24SS ch49-96
WZ3- 2 x 24SS ch97-144
WZ4 2 x 24SS > 8SS > 48lsd ch145-248
WZ5 - 48lsd - 201-248 (mirrored)

last nights new observations in slow/static sequences, that the "hanging?" triac would not release until new/refresher data packet is sent. (usually ~15 seconds) ,or i sent it a 00 manually.

Others reported their 8ss & 16ss are exempt, while i experienced as many if not more of my misfires were on the 8SS.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

It would be useful if people gave a little bit of info about their setup. Which controllers, which baud rate, whether they are using RS232 or RS485 to connect to the first board, what type of lights were having the problem (incandescent vs LED, half-wave vs full-wave, etc).


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
klyneshouse wrote:...last nights new observations in slow/static sequences, that the "hanging?" triac would not release until new/refresher data packet is sent. (usually ~15 seconds) ,or i sent it a 00 manually.

Workaround: Add a single channel at the END of your setup and include it with your last profile. Set all cells in it to full on for the complete duration of the song. This will cause Vixen to send all channel data with every refresh cycle, including your "extra" channel (which isn't connected to anything). I always put my beat track at the very end of the channels for once the song is "set" and working, then I just fill it in. Vixen will send all channel data even if all values are zero because the last channel has a value.


Reply
klyneshouse
Posts: 230
(@klyneshouse)
Reputable Member
Joined: 16 years ago
dirknerkle wrote:Workaround: Add a single channel at the END of your setup and include it with your last profile. Set all cells in it to full on for the complete duration of the song. This will cause Vixen to send all channel data with every refresh cycle, including your "extra" channel (which isn't connected to anything). I always put my beat track at the very end of the channels for once the song is "set" and working, then I just fill it in. Vixen will send all channel data even if all values are zero because the last channel has a value.

ahh great idea putting it at the end of line - much better than what i was thinking -
Thanks !
But it would need to change it say every 1/2 second maybe to keep the refreshers rolling out as it seemed to be about 15 seconds between them at times with no changes. Instead of staying on the entire song duration right?


Reply
Posts: 16
(@welderson)
Active Member
Joined: 17 years ago

Okay, so I have started having flickering problems now as well. I tried all the above fixes, except the Philips surge protector so I tried a few that I had lying around the house and only one that I had took all the flickering away it is a RadioShack 61-407. Looking through the Specifications I found some thing interesting so I thought I would share. http://rsk.imageg.net/graphics/uc/rsk/Support/ProductManuals/6100407_PM_EN.pdf


Reply
SeiRruf
Posts: 97
(@seirruf)
Estimable Member
Joined: 15 years ago

Since my last problem, I have put all my lights up, and filled all the channels.
In vixen, I disabled the channels that were not being used.
Put my boards on 3 different circuits around the house. (mainly 2, but the 3rd one is barely used too).

Now when I run my shows, I only get around 3ish channels flickering, and it is definitely not as bad as it used to be.
I did not get any EMI filters, I did not coil my cords. So this is great news for me! 😀

I am running 22,500 mini incandescent bulbs. No LEDs. 50ms in Vixen. 175ish Channels.

OH! and I noticed that one of the extension cords I was using, had a bad plug that would faintly crackle and spark a little. DEFINITELY problem here. Make sure your extension cords have secure connections! I'd recommend new cords, just to be sure for your display every year. 🙂

As for my channels that barely flicker now, I may get some polarized-capacitors on them, and see if that solves that EMI interference issue.


Reply
lightman
Posts: 1524
(@lightman)
Noble Member
Joined: 19 years ago

Looking good on that display.


Reply
Posts: 216
(@dunnsr)
Reputable Member
Joined: 16 years ago
welderson wrote:Okay, so I have started having flickering problems now as well. I tried all the above fixes, except the Philips surge protector so I tried a few that I had lying around the house and only one that I had took all the flickering away it is a RadioShack 61-407. Looking through the Specifications I found some thing interesting so I thought I would share. http://rsk.imageg.net/graphics/uc/rsk/Support/ProductManuals/6100407_PM_EN.pdf

I looked at all kinds of stuff like this... the only reason that I went with the Phillips is because it was a 5 dollar 1 outlet surge suppressor with emi filtering. the only problem that I can see with them is that you need one for every circuit in your house that you have lights connected too... In my instance, I ran 6 dedicated 20 amp circuits specifically for the show... so i have to buy 4 more of the surge protectors... the good thing is that i even have two of my all led boards connected into one circuit with no issues.

so in response to P short...

I have 10 Ren 24 SS's running DMX followed by 2 ren 48LSD's one v3b one v3c.
all of my leds are cheapo walmart strait out of the box, no full wave conversions or anything.
all of my sequences are 50 ms except sandstorm which is 25 ms.

I have over 3000 ft of extention cord and stuff running through the yard, so i am sure thats why i have all of the EMI issues.

here are the steps that I have taken per the forums recoomendations
1. copy and paste all sequence data into new "clean" sequences.
1.5 deleted everything in the sequence that happened on the first 2 boxes of every channel and the last two boxes of every channel
2. I checked baud and all of that but when your running dmx its all preset.
3. put snubbers on EVERY channel. i did this via a 47k ohm resistor placed across the actual screw terminals in the box ( i am too cheap to buy a bunch of plugs and it does not matter where in the circuit they are placed... so i just put them right on the boards.)
4. seperated all data/ext cords to the best of my ability in the yard, coiling all extra ext cord tightly.
5. moved every led board to a non led board (since i only have 3 non led boards, i still had issues)
6. bought the cheap phillips surge protector. placed it inline with led boards having issues... seemed to clean up everything.

after all of these things my results.

once i did all of these things, i have a 98 percent clean show... i still am in need of a few more phillips plugs, and i think that will clean it up nicely!

for those of you wondering how i waterproofed the surge supressor, i bought at walmart they have plastic tubs they call shoe boxes... they are about eh size of a shoe box... i dremmeled out a couple notches very close to the top for the cords, plugged eveyrhting in inside, put on the lid... threw some silicone on the cords and voila!

this IS my first year... but i think it is very successful thus far... if you have questions about other stuff i have done i would love to help if i can

seth


Reply
Wayne J
Posts: 7789
(@wayne-j)
Illustrious Member
Joined: 20 years ago

That would be a thorough test, I would think. Now, what I would be curious about, if anyone feels zealous,....
What would happen, to keep the Surge Protector/EMI filter on, and remove the resistor snubber plugs?


Reply
Page 1 / 9
Share: