Renard SS24 First H...
 
Notifications
Clear all

Renard SS24 First Hookup

6 Posts
3 Users
0 Reactions
2,095 Views
Posts: 706
Topic starter
(@chadowamsley)
Prominent Member
Joined: 15 years ago
[#18472]

Any help is appreciate. Sorry if my text doesn't flow nicely, but grammar never was my strong point, and trying to give all the details to what I have.

I have my first Renard ss24 built, the chips came programmed with the firmware since my programmer hasnt arrived. I'm sure I am just missing an important step, besides not having the diagnostic firmware to test. I was debating asking this until my programmer arrives so that I can run the diagnostic firmware, and reflash the chips to make sure they are correct, but I wanted to try and see if I could get blinky before purchasing the rest of my boards in the group buy Saturday.

I hook up my usb to rs485 as shown in the Wiki. I just cut one end of a ethernet cable I was not using. Orange and orange white to the ground, blue and blue white to the correct inputs, and the other 4 wires not hooked up. Maybe they need hooked up, but I did not see them in the wiki so I left them hanging. The input goes into the j2 input. JP1 and JP2 are installed on the board. I add the renard plugin into my profile in vixen along with adding the channels. I setup the com port3 in the settings. Adjustable preview is still selected also. I add power to the board, and my green light on the board comes on. I only plugged one cord into the first channel, was only wanting to see it work. I disabled the other channels in my profile, except channel one. When I click play in Vixen, adjustable preview comes up, but nothing on the string of lights happens. Vixen does recognize the board, I think, since the preview and all works after selecting the renard plugin. On the board input and output, I did not crank the terminals down but they were snug to hold the wire.

Am I suppose to change my port from the default port 3 ? Or do something on the actual pc itself for the port ? Or am I just missing something in Vixen ? This is my first year, and maybe jumping the gun considering I didnt test with any diagnostic firmware, but like I said I was hoping to see a blinky before Saturday. Just so I know what I build will work before purchasing a large buy for more. Thankful for any info you can send my way. I have checked the forums, most of last night, but didn't see my answer.

Thank You,


5 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

If you have an RS-485 adaptor and NOT an RS-232 adaptor then JP1 should be OFF.


Reply
underdog
Posts: 185
(@underdog)
Estimable Member
Joined: 17 years ago

Off the top of my head,
Hardware: What type of connection between the DB9 and the RJ45. Do you have an adapter? Did you check to make sure the color scheme matched what the wiki suggested? My adapter revealed a different color scheme than that the wiki, I used my multimeter to match the pins to the color wire. I'm also assuming you have a USB to RS485, not to be confused with RS232. Another problem you may have is that their is a few different schemes for CAT5 pinouts, look at the keystone end of the wire you're using, see if you can positively identify that the the colors match the 568B scheme.

Software: Find what comm port your using, Control panel>System properties>Hardware tab>Device manager>...I use a serial comm port, however, you may have to use driver software to distinguish USB and identify it as a Comm port. (shown as "Universal Serial bus Controller"). In Vixen, make sure "Renard output plugin" is checked. Also, your channel output may be different than you think, just to check communication, use the "test channels" to see if one/all of the channels light.

Firmware: There have been a few people who claim that their PIC's were wiped in shipping, I cannot confirm or deny that.


Reply
Posts: 706
Topic starter
(@chadowamsley)
Prominent Member
Joined: 15 years ago

I seen in the Wiki where JP1 was not needed, but was afraid not to install it. That could possibly be a cause in the channel not lighting ? Not saying that is my case, but could be. If one is using the usb to rs485, the jp1 would not allow it to work correctly. With the adapter, could I just wire the cat5 into it, but rather then using the usb part, could I just plug it in directly to a serial port to see if it would work ? Or would one of the parts still need removed ? I have a serial port on the actual pc Ill be using for my show, just not on my laptop that I do my sequencing on. So I could hook it up either way.

I am using an usb to rs485 adapter. My color code on the cat5 matches that of the 568B, and my orange and orange white goes to the ground on the adapter, and then my blue and blue white goes in as the Wiki shows. I dont remember the exact locations of those but one is + and one is -, then the other 4 wires in the cat5 are left hanging not hooked up. I checked the channel output in my profile, and the settings for the renard plugin and com port. After I installed my adapter drivers, vixen only showed com port 3 to select. I will go through control panel and double check that. I will try the test channels tonight. Im just looking to see if they all fire in my preview?

The JP1 being installed, or pics being wiped, are the two things I was leaning towards but was rather hoping for a simple checkbox check. Couldnt be that easy though.

Thank You for the replies. I will try the suggestions tonight. Still waiting on my programmer.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

It's pretty clear - if you are using RS-485 then JP1 must be OFF - if using RS-232 then JP1 must be ON - it's that simple. If JP1 is on, it will short out one of the differential data paths from the RS-485 interface (there is a D+/A and D-/B data path).

The wiki is clear on the cabling as well - just follow the pinout diagrams.


Reply
Posts: 706
Topic starter
(@chadowamsley)
Prominent Member
Joined: 15 years ago

Thank you. I will remove the JP1 on this board and remember that on the next one.


Reply
Share: