Little back history, I bought 2 Ren24SS boards from one of last year's group buys. I assembled both boards, and except for 1 channel that won't light, both boards worked fine. The previous year I had a simple show using just a simple Arduino board, a hacked Mr Christmas and some switched.
So my brilliant plan was to combine the 2 systems and extend my show...
Except the two wouldn't talk together at all. I spend numerous hours on it and eventually gave up. Then the worst happened. Both Renards went dark on me. The power light goes on (maybe some other indicators, can't remember at this moment), but that's about it. As I was changing code on the Arduino during this process, and it connects with the com port, I am thinking that I might have sent instructions down the wrong COM channel at some point (probably just before they went dark). The computer had been flipping out a little, giving me new ports as I was plugging and unplugging different components.
This weekend I pulled out the Renards, thinking that it might have been just the first of the 3 pics that got zapped with the wrong code and replaced it with a spare I had. Nope. Replaced all 3 with the 2nd unit. Nada, zippo. 😥
I have no idea what to do at this point. Can anyone think of anything else I can try/test/do to see if I can get this thing going again? Do I need to re-download the code to the chips? If so, how do I do that? I'm not beyond making some testing board, or some sort of "download the instructions from the computer to the chip" board, just need guidance from you all old salts.
TL/DR: MacabreRob is a moron.
Thanks for reading.
How are you connecting to the pc usb adaptor? if so make sure its not a prolific one there know to bluescreen and randomly rest like that.
Also pictures of the boards would help. IF you blew up anything its likely the differential driver chip aka: ttl to rs232/485 converter. Also make sure the jumpers are set correctly per the guide in the wiki.
REN's don't get reflashed in place, so "sending the wrong data down the serial stream" should be harmless.
At this point you have two board that were working just fine, and I'm assuming were connected to the same serial port.
Now they are DARK. The common point of failure, is the PC and/or the serial port from the PC.
Check you serial settings... are these USB2Serial adapters? Could they have enumerated as different COM ports? (you said perhaps they did?)
Check your Vixen profile(s)... perhaps you disabled the REN's from the profile?
Do your USB/Serial adapters have Transmit/Receive LEDs on them? Use those to verify if data is making out of the PC to begin with.
Just some thoughts.
MacabreRob wrote:Little back history, I bought 2 Ren24SS boards from one of last year's group buys. I assembled both boards, and except for 1 channel that won't light, both boards worked fine. The previous year I had a simple show using just a simple Arduino board, a hacked Mr Christmas and some switched.So my brilliant plan was to combine the 2 systems and extend my show...
Except the two wouldn't talk together at all. I spend numerous hours on it and eventually gave up. Then the worst happened. Both Renards went dark on me. The power light goes on (maybe some other indicators, can't remember at this moment), but that's about it. As I was changing code on the Arduino during this process, and it connects with the com port, I am thinking that I might have sent instructions down the wrong COM channel at some point (probably just before they went dark). The computer had been flipping out a little, giving me new ports as I was plugging and unplugging different components.
This weekend I pulled out the Renards, thinking that it might have been just the first of the 3 pics that got zapped with the wrong code and replaced it with a spare I had. Nope. Replaced all 3 with the 2nd unit. Nada, zippo. 😥
I have no idea what to do at this point. Can anyone think of anything else I can try/test/do to see if I can get this thing going again? Do I need to re-download the code to the chips? If so, how do I do that? I'm not beyond making some testing board, or some sort of "download the instructions from the computer to the chip" board, just need guidance from you all old salts.
TL/DR: MacabreRob is a moron.
Thanks for reading.
What is the interface from PC to Renard - RS232 or RS485 (or DMX)? Check the "JP1" jumpers on the boards. If you are using RS232, it should be on the first board from the PC only (Renards are always RS485 OUT). If you are all RS485 then you should not have that jumper on.
I agree that the most likely issue is the Com port. But if you need a bit of comfort, take the first PIC in one of the boards and flash the diag image on it. Plug this board into the serial port from the PC. Send something from the PC. If you do not get any lights flickering, then the (four major possibilities) PC is not sending anything, your adapter may be broken, or your cable may be bad, wrong RS232/RS485 selection. If the OR and/or FE lights come on, you probably have the wrong baudrate or the cable may be bad, If the Data light comes on without errors then you may be sending empty frames.
