Renard 24 Programmi...
 
Notifications
Clear all

Renard 24 Programming

8 Posts
6 Users
0 Reactions
5,335 Views
Posts: 4
Topic starter
(@alm4511)
Active Member
Joined: 15 years ago
[#15990]

I'm in the process of building my first Ren24, V3.3, and have some questions because I know very little about PICs. Before I can use the Ren24, do I need to program the PICs, or can I run directly from Vixen? From what I'm ready online, I have to program them first, but how? Any suggestions?

Best regards,

Allen Miller


7 Replies
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Look at the second thread in the 'How-To' section of this forum.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
alm4511 wrote:I'm in the process of building my first Ren24, V3.3, and have some questions because I know very little about PICs. Before I can use the Ren24, do I need to program the PICs, or can I run directly from Vixen? From what I'm ready online, I have to program them first, but how? Any suggestions?

Best regards,

Allen Miller

Allen, welcome to DIYC! There is a wealth of information here and lots of people chomping at the bit to chime in and help. Getting familiar with the WIKI (link at the top of the page) is a really solid idea, since the hundreds of pages and photos available there exist to help folks get started with the DIY gear. And like Phil said, the threads are worthy of some face-time, too!!!

Don't be afraid to look around and of course, don't be afraid to post stuff and not only ask questions, but give everyone progress reports, or discuss your plans for the display, or for technical how-to information. But most of us here would probably agree that the Wiki can be your best friend!!!

-dirk


Reply
Posts: 4
Topic starter
(@alm4511)
Active Member
Joined: 15 years ago

Thanks for the info. So, I think I need an iCP02 - USB PIC Programmer (3.3V/5.0V) and an iCP03v2 - Multi PIC & EEPROM Adapter for programming the PIC outside of the circuit. To communicate with the iCP02, I can download Microchip's PICkit 2 or MPLAB IDE. MPLAB IDE is probably all I will need since I will already have a PIC programmer. PicKit2 is a complete kit.

So, I could purchase the iCP02 - USB PIC Programmer (3.3V/5.0V) and an iCP03v2 - Multi PIC & EEPROM Adapter from piccircuit.com for $27.00 and download MPLAB for free, or I could purchase PICkit2 starter kit from Microchip for $50. Any suggestions or am I way off the mark?

Al


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

Pickit 2 is the most common used here so you'll be able to get the most help. Several people have the pickit 3 and recommend that for a couple bucks more and more ability. I think if I had not bought the pickit 2 used I'd get the pickit 3

Brian


Reply
tstraub
Posts: 525
(@tstraub)
Honorable Member
Joined: 18 years ago

I have had an iCP02 and it has worked well for 2 years. It works great with the Microchip software both MPLAB IDE and Pickit2 software. To me it feels a little cheap to pick it up and use it. I'm always half afraid I will break it. But it is still working like new and was less expensive than a real Pickit so I guess you get what you pay for.

I also own a PICkit3 and I highly recommend it. It has a lot more robust feel to it seems like it will be more durable in the long run. Microchip offers a 25% discount to students so if you happen to be a student or have a child with a student email address you could get the real thing for about the same price as the clone.

Either one should be fine for you it really just depends your budget and how much you think you will use it in the future

just my $0.02
Tyler


Reply
Posts: 371
(@gebbinn)
Reputable Member
Joined: 16 years ago

Just to answer the question, you can download both the PicKit software and MPLabs software for free. if you feel like going for the less expensive hardware, software will not be the problem.

Still, as alluded to above.. You dont get what you dont pay for.


Reply
Posts: 4
Topic starter
(@alm4511)
Active Member
Joined: 15 years ago

Thank you for the quick responses. I apologize for my late replies, for I still have small children and they demand much of my time. 🙂

OK. I purchased the PicKit2 and read the manual, mostly. I downloaded the firmware hex file from http://www.kostyun.com/?page_id=139/ and programmed my PICs. I am using Vixen to communicate with the Renard via com1. I have an oscilloscope and can see data on pin 5 of U3 when I run the routine through Vixen. I know I have 5V throughout the board, but no lights other than power are lit. HB Diag, ZC Diag, Comm OK and Comm FR do not light. What am I doing wrong?

Many thanks,

Al


Reply
Share: