Notifications
Clear all

Ren24HC

32 Posts
9 Users
0 Reactions
9,140 Views
Posts: 127
Topic starter
(@baboiler)
Estimable Member
Joined: 15 years ago
[#21585]

I hope to begin (and finish) my Ren 24HC board this week.

I found info on the wiki for testing the 24SS boards but I could not find anything on test procedures for the 24HC. Am I overlooking it somewhere on the wiki?


31 Replies
FIRECOP252
Posts: 1292
(@firecop252)
Noble Member
Joined: 16 years ago

Its not on the WIKI and his site is down....If I remember from building mine last year there was not any testing procedures just for the 24HC but you might be able to test it in a similar fashion as the 24SS.


Reply
g2ktcf
Posts: 3651
(@g2ktcf)
Famed Member
Joined: 18 years ago

Lance is correct....the labels on the parts are different but the procedures are the same. This is something I have been trying to get to for some time now as the entire wiki for the 24HC needs rewriting.

If you have any specific questions on the cross-over, please post them here so we can all lend you a hand!


Reply
LightUpMA
Posts: 208
(@lightupma)
Estimable Member
Joined: 15 years ago

I just finished my ren 24 hc and have a question ...

Everything appears ok but when I hit the test points. Tp2 gives me 5 as it should. But 3-5 give me 7.6, 3.75, and 3.8 respectively.

It says they should be 12. Am I missing something? I hope it's something simple. Thanks!

-wayne


Reply
RichF
Posts: 1356
(@richf)
Noble Member
Joined: 19 years ago

TP 4 and 5 are AC voltage


Reply
LightUpMA
Posts: 208
(@lightupma)
Estimable Member
Joined: 15 years ago
RichF wrote:TP 4 and 5 are AC voltage

Does anyone know what it means when values are far below the 12 volts it says it should be?


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago
LightUpMA wrote:Does anyone know what it means when values are far below the 12 volts it says it should be?

What Rich is telling you is to change your multimeter to AC and see what it says 🙂


Reply
RavingLunatic
Posts: 1502
(@ravinglunatic)
Noble Member
Joined: 19 years ago
LightUpMA wrote:I just finished my ren 24 hc and have a question ...

Everything appears ok but when I hit the test points. Tp2 gives me 5 as it should. But 3-5 give me 7.6, 3.75, and 3.8 respectively.

It says they should be 12. Am I missing something? I hope it's something simple. Thanks!

-wayne

I wouldn't waste too much time worrying about TPs 3-5 as long as TP2 has a steady +5VDC then you have what the board needs to operate correctly. The other TPs are before the voltage regulator and really don't matter as long as you have the +5VDC at TP2.


Reply
LightUpMA
Posts: 208
(@lightupma)
Estimable Member
Joined: 15 years ago
kychristmas wrote:What Rich is telling you is to change your multimeter to AC and see what it says 🙂

Oh wow ... Brain on vacation - now I gotcha! Thanks guys!


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago
LightUpMA wrote:Oh wow ... Brain on vacation - now I gotcha! Thanks guys!

I never use the test points. I would follow RavingLunatic's instructions and not worry too much about it. Just get your data cable hooked up and see if it works.


Reply
Page 1 / 4
Share: