Murphy strikes agai...
 
Notifications
Clear all

Murphy strikes again

8 Posts
4 Users
0 Reactions
2,700 Views
klm
Posts: 169
 klm
Topic starter
(@klm)
Estimable Member
Joined: 15 years ago
[#17435]

Of course on our 'dry run' all boards work perfeclty, tonight, 1.5 hours before judging, boards in jeep2 and 3 decide not to work. Kept troubleshooting with 1 song for about 45 minutes, it would work for a couple of seconds, and stop for about 20 seconds. changed out 3 inverters in jeep 2, notta. Electricians got out thier testers, no clue. Checked solders, cords.....
Gave up on our jeep went to jeep 2, I moved the board in our jeep (3) from the top down to the console, after a while it started working. This was also after I switched out songs, but after a bit, not right away. As time went on our board started working more than not. It only cut out 3 or 4 times during the parade, leaving it down and just playing 1 song.
The other board we got working for #2 by plugging body channel lights directly to inverter to on all the time, left other 3 channels plugged in and had the passenger hold it in front of her verticle. Again, no clue but we pulled it off. Tomorrow, forcast is rain....maybe.
Wizards of Winter did not make those boards as happy as Mad Russian Christmas.
Mad Russian Christmas it was, the whole parade.

Ours acted like it wanted to be warm. On top was too cold? Who knows, it worked. Keep our fingers crossed for tomorrow.


7 Replies
Materdaddy
Posts: 2368
(@materdaddy)
Famed Member
Joined: 16 years ago

So you're using inverters to control AC lights? I've wondered how well those work based on the output of the wave going into the H11AA1 for zero cross. I have heard that can do strange things because inverters put out a more "square" wave, even when they advertise a sine wave.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Linda, I sent a couple PM's to Chad. More often than not, it turns out to be a solder joint that's become loose when the temperature drops. But because you are using inverters, the voltage coming out of those inverters could create an issue with the 5v voltage regulator, putting it into a "dead zone" which shuts it down. Check the output voltage, if it's 120vac or less you're probably okay but if it's greater than 120vac, you might need to replace the 5v regulators with plain-jane 7805 regulators. Pick them up at any Radio Shack.


Reply
klm
Posts: 169
 klm
Topic starter
(@klm)
Estimable Member
Joined: 15 years ago

Thanks again! I will make sure he gets this too. I think soldering because they check the voltage of jeep 2 and it was 94. It was about 32degrees. Tonight is supposed to be a little warmer but maybe rain.
I didn`t think it was too be so physical, i feel like I was run over by a Mac truck. C`mon motrin....


Reply
klm
Posts: 169
 klm
Topic starter
(@klm)
Estimable Member
Joined: 15 years ago

Something to add, I was totally impressed with the fm02 and test antenna. The sound quality was great, i hear we broadc asted about 2 blocks, Chad brought a third battery just in case but when trying to recharge all of them, they all still say fully charged. The fire dept was very curious and had a lot of questions about our set up, i gave them the run down and you should have seen his face when i told him we could be separated 1/4 miles and we still blink. Barring our technical difficulties with the 2 boards i still feel it was a success and you should have seen the faces on the crowd as we passed, the kids and especially the men, i could see their wonder and fascination. We are working on video now, we have one in facebook but he want to clean it up a bit before youtube. Video is very difficult because we are a moving target so he had to do a lot of walking backwards. I will definitely share here as soon as I can.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago
dirknerkle wrote:Linda, I sent a couple PM's to Chad. More often than not, it turns out to be a solder joint that's become loose when the temperature drops. But because you are using inverters, the voltage coming out of those inverters could create an issue with the 5v voltage regulator, putting it into a "dead zone" which shuts it down. Check the output voltage, if it's 120vac or less you're probably okay but if it's greater than 120vac, you might need to replace the 5v regulators with plain-jane 7805 regulators. Pick them up at any Radio Shack.

I'm confused about what you're saying. Why would a voltage greater than 120VAC cause problems?

Do you know what type of waveform the inverters are generating? It should be reasonable close to a sine wave, a square wave would cause problems with the ZC logic. Of course, even mentioning a square wave in this context might possibly be dating me.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
P. Short wrote:I'm confused about what you're saying. Why would a voltage greater than 120VAC cause problems?

Do you know what type of waveform the inverters are generating? It should be reasonable close to a sine wave, a square wave would cause problems with the ZC logic. Of course, even mentioning a square wave in this context might possibly be dating me.

The original MiniRen8/4XB and MiniRen8/8XBs used a LF50CV 5v regulator which worked fine as long as your source voltage was not > 18 and < 40 vdc which caused the regulator to go into shutdown mode. This was one of those "fine print" kind of notations that's easy to miss on the spec sheet which stated 30vdc as the maximum input voltage. The 12v transformer used typically delivers around 15-16vac to the rectifier but that's based on input voltage 120vac, the transformer might deliver 17 or 18 volts to the rectifier, which could then cause the LF50CV to start up for a bit and then go into shutdown mode. An automobile inverter could conceivably deliver >120vac, especially when the motor is revved, which could then create the domino effect to cause the shutdown to occur.

A common 7805 is a good solution, and another regulator that does not have the dropout quality was suggested as a substitute.

I've tested an SS8 as well as the MiniRen boards using an inverter and they both seemed to work fine. I'm fairly certain that it did not have a sine wave or even a modified sine wave, but I've never checked. Now you've got my curiousity up to check the inverter's wave pattern.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

I suspect that the results may vary, depending on the inverter. I think that any recent or high-quality inverter would output something close to a sine wave, but that some older ones might not.


Reply
Share: